Ellison AllStar Mode D'emploi
  1. Manuels
  2. Marques
  3. Ellison Manuels
  4. Cisailles
  5. AllStar
  6. Mode d'emploi

Ellison AllStar Mode D'emploi

Masquer les pouces

Publicité

Table des Matières

SM
Instructions for Use of
AllStar
Die-Cutting System
®

Publicité

Table des Matières
loading

Manuels Connexes pour Ellison AllStar

Sommaire des Matières pour Ellison AllStar

  • Page 1 Instructions for Use of AllStar Die-Cutting System ®...

  • Page 2: Table Des Matières

    Instructions in Other Languages French German Spanish For additional help, call Ellison within USA 800.253.2238 or outside USA 949.598.8822 or within UK 0871 222 2277 or outside UK +44 (0) 845 345 2277 within USA Fax 800.253.2240 or outside USA Fax 949.598.8835...

  • Page 3: Safety Instructions

    CUTTING AREA ONCE HANDLE IS LOWERED. ALWAYS KEEP A FIRM GRIP ON THE HANDLE AFTER EACH CUT WHEN RAISING IT BACK UP. DO NOT OVERLOAD THE MACHINE. CUTTING HAZARD. AVOID CONTACT WITH THE ALLSTAR DIE BLADE. ADULT SUPERVISION OF CHILDREN RECOMMENDED.
  • Page 4 The Ellison AllStar die-cutting system consists of the AllStar Machine, steel-rule dies and a Die Storage Rack (each sold separately or in kits, refer to Ellison AllStar catalog or visit Ellison.com/educators for details). This value-added package gives you the same outstanding brand quality that you have come to expect from Ellison.
  • Page 5 Place material to be cut against the foam side of the die. Place the material and foam against the Cutting Pad, foam side down. Slide the Cutting Pad with Pressure die and material into the Plate machine until the first alignment icon (indicated by a star (1) and a line on the back of the die) is at the...
  • Page 6 Slide the Cutting Pad toward the front of the machine and remove the die and die-cut shape. Your beautiful die design is Shim cut and ready for use. Base Plate Please note: If the die-cut shape is not completely cut, add one Shim (located in the drawer) onto the base plate.

  • Page 7: Helps & Hints

    To ensure longer life of dies, it is recommended to store your AllStar Dies in an AllStar Die Storage Rack (sold separately) in a cool and dry place. To ensure optimal...
  • Page 8 Problem: Only half of the shape is cut completely. Solution: Make sure that you are using the alignment icons on the AllStar Dies as mentioned in the instructions. Problem: Edges of the die-cuts are rough and ragged. Turn over or replace Cutting Pad.

  • Page 9: Materials Guide

    Materials Guide Leather Balsa Wood Magnet, Flexible Sheets Bubble Wrap Magnet, Self-Adhesive Butcher Paper Metallic Foil Board Cardboard Personalized Embossing Cardstock Plastic (PEP) Chipboard Plastic, Shrink Film Construction Paper Poly Foam Construction Paper, Poster Board Laminated Quilt Batting Cork, Self-Adhesive Rubber, Self-Adhesive Corrugated Paper Sandpaper, Fine 00...

  • Page 10: Warranty

    What Does This Warranty Cover? AllStar Limited This warranty covers any manufacturing Warranty defects in your Ellison AllStar die-cutting Machine (the “Product”). How Long Does The Warranty Last? This warranty lasts for 3 years following your date of purchase of the Product. You...
  • Page 11 +44 (0) 845 345 2277 outside UK A Return Authorization (RA), along with shipping information, will be issued. Following a determination by Ellison that a fault covered by this warranty may have occurred, Ellison will: (a) ship you replacement parts or (b) ship you a replacement Product.

  • Page 12: French

    4. Placez la matrice AllStar sur la plaque de découpage, avec la partie en mousse face vers le bas, la partie avec l'étiquette vers l'avant de la machine, et insérez le matériau à...
  • Page 13 Problème: Le bas de la forme découpée en papier est chiffonné. Solution: Tirez sur la manette de la machine AllStar de seulement 10,16 cm (4 po) après avoir commencé à forcer OU découpez une seule feuille de papier à la fois OU changez la plaque de découpage.

  • Page 14: German

    3. Nehmen Sie das Schnittbrett aus der Vorderschublade und legen Sie es auf die Arbeitsfläche des Geräts . 4. Legen Sie einen AllStar Lochstempel auf das Schnittbrett, und zwar mit der Schaumgummiseite nach unten, so dass das Etikett daran zur Vorderseite des Geräts zeigt, und danach das Material, das geschnitten werden soll, zwischen den Lochstem- pel und das Schnittbrett.
  • Page 15 Material nicht mehr wellt. Problem: Die Unterseite des ausgestanzten Papiers ist faltig. Lösung: Ziehen Sie nur 10 cm nach dem Widerstand am Griff des AllStar Geräts weiter ODER stanzen Sie jeweils nur ein Papier ODER tauschen Sie das Schnittbrett aus.

  • Page 16: Spanish

    área de trabajo de la máquina. 4. Coloque una matriz AllStar sobre la almohadilla de corte (el lado de espuma hacia abajo y el lado de la etiqueta hacia la parte delantera de la máquina) y el material para cortar entre la matriz y la almohadilla de corte.
  • Page 17 Problema: El lado inferior de la matriz de papel está arrugado. Solución: Tire de la manija de la máquina AllStar solamente 10 cm a partir del punto en que empiece a sentir resistencia O corte una hoja de papel cada vez O cambie la almohadilla de corte.
  • Page 18 For additional help, call Ellison within USA 800.253.2238 or outside USA 949.598.8822 or within UK 0871 222 2277 or outside UK +44 (0) 845 345 2277 within USA Fax 800.253.2240 or outside USA Fax 949.598.8835 ellison.com/educators © 2008 Ellison A10000 All Rights Reserved 09.15.08...

Table des Matières