Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Publicité
Manuels Connexes pour Ooni 3
Sommaire des Matières pour Ooni 3
- Page 1 GAS BURNER FOR OONI 3 MANUAL...
- Page 2 For use with LPG (Propane) Gas only. Use only with supplied Gas regulator. Register your Ooni 3 Gas Burner FSD at ooni.com For the full user guide, cooking instructions, tips and tricks please visit ooni.com...
- Page 3 (ii) the entirety of the provisions of the Ooni 3 oven’s Safety Legal Disclaimer also apply to the use of the your Ooni 3 Gas Burner FSD attachment part in addition to the provisions of the present safety legal disclaimer. You are strongly advised to not use your Ooni 3 oven with the Ooni 3 Gas Burner FSD attachment part until your Ooni 3 oven has been thoroughly and properly gas leak-tested.
- Page 4 Ooni 3 oven or any other appliance. You shall use your Ooni 3 Gas Burner FSD attachment part, in connection with your Ooni 3 oven, only with pre-bottled LPG (propane). Improperly stored LPG (propane) is a hazard due to possible gas release from the safety relief valve.
- Page 5 The appliance must be kept away from any flammable materials during use. • When changing the gas canister, ensure that the Ooni 3 Gas Burner FSD knob is turned to the off position, disconnect the regulator from the gas canister and remove the canister. Throughout this process, ensure that the canister is kept a minimum of 1 meter (3.5ft) away from the oven to avoid...
- Page 6 Diagrammatical Representation of Outdoor Areas • Outdoor Area - Example 1 • Outdoor Area - Example 2 • This appliance shall only be used in an above ground open-air situation with natural ventilation, without stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural convection.
- Page 7 Ooni 3 Gas Burner Parts required: Ooni 3 Gas Burner FSD Gas hose Install hose pipe Tools required: Wrench x2 USA / CAN tighten with suitable wrenches...
- Page 8 tighten with suitable wrenches...
- Page 9 Step 1 Parts required: Assembled Ooni 3 with Remove the door, flame guard Ooni 3 Gas Burner FSD and fit chimney cap Warning The door should removed at all times during use with the Ooni 3 Gas Burner FSD...
- Page 10 Step 2 Parts required: Assembled Ooni 3 Remove pellet burner Allen key...
- Page 11 Step 3 Parts required: Assembled Ooni 3 Install Ooni 3 Gas Burner FSD Ooni 3 Gas Burner FSD...
- Page 12 Step 4 Parts required: Assembled Ooni 3 with Secure Ooni 3 Gas Burner FSD Ooni 3 Gas Burner FSD Allen key Gas bottle Secure but do not over tighten bolts...
- Page 13 • An LPG cylinder shall be of a maximum nominal 20 lb (9.1 kg) fuel capacity. • Use a suitable provided regulator certified to ANSI Z21.18/CSA 6.3 and a flexible hose certified to ANSI Z21.54/CSA 8.4. • The regulator shall be installed in such a location that it will not attain a temperature above 130°F (54.5°C) •...
- Page 14 POL gas regulator This is an anticlockwise threaded gas fitting. Ensure the tank is fully turned off and screw the regulator on to the gas tank valve fitting until tight. Gas Safety Information • The appliance must be installed at least 1 meter from any flammable materials. •...
- Page 15 Step 5 Parts required: Assembled Ooni 3 with Igniting your burner Ooni 3 Gas Burner FSD Push in and slowly turn the control knob anticlock- wise until you hear a click and the burner ignites. Continue to push and hold in the knob for 5 seconds before releasing.
- Page 16 Verify that Ooni 3 Gas Ooni 3 Gas Burner FSD Burner FSD is on If not, turn off the gas and go back to Step 5 If Ooni 3 Gas Burner FSD still does not ignite go to Step 7...
- Page 17 Step 7 Parts required: Assembled Ooni 3 with If Ooni 3 Gas Burner FSD still does Ooni 3 Gas Burner FSD not ignite Match holder Turn the gas on and light using a match and the supplied match holder through the front of the oven...
- Page 18 0.83 mm MARKING (MARKED 0.83) Model number: Ooni 3 GAS BURNER FSD WARNING: DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION. DO NOT USE OR STORE FLAMMABLE MATERIALS IN OR NEAR THIS APPLIANCE.
- Page 19 Lorsque vous utilisez le four Ooni Pro avec votre Brûleur four Ooni Pro ou de tout autre appareil. N’insérez d’outil à gaz Ooni 3 FSD, gardez à l’esprit que (i) le Brûleur à gaz ou de corps étranger dans la vanne de sortie ni dans Ooni 3 FSD ne peut être utilisé...
- Page 20 JAMAIS de bouteille de GPL (propane) de rechange sous Toujours utiliser des gants de protection lors de la ou à proximité de votre four Ooni Pro ni dans un endroit manipulation de composants chauds. fermé. Une bouteille de GPL (propane) non connectée ne Le stockage d’un appareil à...
- Page 21 (ii) au moins 30 % de la superficie restante des murs doit Renseignements de Sécurité relatifs au Gaz être ouverte et dégagée. L’appareil doit être installé à au moins 3.5ft (1 mètre) de Dans le cas des balcons, au moins 20 % de la surface tout matériau inflammable.
- Page 22 Le four doit être placé sur une surface non inflammable, l’étape 5 stable et plate. Si le bruleur à gaz Ooni 3 FSD ne s’allume toujours pas, Assurez-vous que votre four soit placé dans une zone qui passer à l’étape 7 ne sera pas affectée par les intempéries.
- Page 23 Ne modifiez pas l’appareil. AVERTISSEMENT : N’utilisez que la porte pour pizza que lorsque le Brûleur à gaz Ooni-Pro est allumé. La porte avec thermomètre ne doit pas être utilisée. AVERTISSEMENT : Si des flammes sortent, coupez l’alimentation en gaz et attendez 5 minutes avant de...
- Page 24 © 2019 Ooni Ooni is a registered trademark of USA v1.0 Ooni Limited. All rights reserved...