Know Your Product; Operation Instructions - SPARKY TKN 80D Notice Originale

▪ Never aim the beam at any person or an object other
than the workpiece.
▪ The laser beam shall not be deliberately aimed at
personnel and shall be prevented from being directed
towards the eye of a person for longer than 0.25 s.
▪ Always ensure the laser beam is aimed at a sturdy
workpiece without reflective surfaces. I.e. wood or
rough coated surfaces are acceptable. Bright shiny
reflective sheet steel or the like is not suitable for laser
use as the reflective surface could direct the beam
back at the operator.
▪ Do not change the laser light assembly with a different
type. Repairs must be carried out by the laser manu-
facturer or an authorised agent.
WARNING: Use of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
VI - Know your product
1. Laser assembly
2. Laser light on/off switch
3. Laser cover
4. Laser pitch control
5. Saw arm
6. Release knob
7. Operating handle
8. Carrying handle
9. Upper fixed blade guard
10. Clamp assembly
11. Clamp assembly lock
12. Rotating blade guard
13. Guard retraction arm
14. Blade bolt cover
15. Dust bag
16. Bevel lock
17. 0° Bevel adjuster
18. Bevel scale
19. Fence
20. Stabiliser
21. Hex key, 6 mm
22. Mitre table
23. Mitre scale
24. Table insert (kerf plate)
25. Switch trigger
26. Mitre lock
27. Spindle lock button
28. Dust extraction port
29. Slide bars
30. Slide bar lock
31. Trenching depth adjustment screw
32. Trenching stop
33. Trenching depth lock nut
34. 45° Bevel adjustment screw (left)
35. 45° Bevel adjustment screw (right)
36. 0° Bevel adjustment screw
37. Release latch
38. Side extension arms (x 2)
39. Side extension arm locking screws (x 2)
6
EN
pages-TKN-80-95D-2012.indd 6
VII - Operation instructions
This model SPARKY power tool is supplied from single-
phase alternating current mains. It is double insulated
according to EN 61029 and IЕС 61029 and can be con-
nected to grounded or not grounded sockets. This power
tool is radio suppressed in compliance with EMC Direc-
tive 2004/108/EC.
PRIOR TO INITIAL OPERATION
Before starting to operate the saw, always check the fol-
lowing:
▪ Make sure power supply voltage corresponds to the
value, indicated on the name plate with technical data
of the tool;
▪ Always check the position of ON/OFF switch. The
power tool must be connected to the power supply
socket only when this switch is in OFF position;
▪ Always inspect the blade. Use only well ground
blades. Never use blades with cracks and indents or
HSS-blades.
▪ Make sure that all moving parts of the blade guard
move freely.
▪ Make sure the work piece or the material is well se-
cured.
▪ Make sure that the cord and the plug are in order. If the
replacement of the supply cord is necessary, this has
to be done by the manufacturer or his agent in order
to avoid a safety hazard.
ACCESSORIES
The tool is supplied with the following accessories: hex
key, 6 mm (Fig. 1a); blade (fitted) (Fig. 1b); dust bag
(Fig. 1c); 2 x side extension arms (Fig. 1d); workpiece
clamp (Fig. 1e); 1 x stabiliser (fitted) (Fig. 1f).
To achieve best results we recommend using genuine
SPARKY accessories.
TRANSPORTATION
Lift the mitre saw only when the saw arm is locked in the
down position, the saw is switched off and the plug is
removed from the power point.
You must only lift the saw by the carrying handle (8) or
outer castings. Do not lift the saw using the guard or op-
erating handle (7). (Fig. 2)
BENCH MOUNTING
The saw base has holes to facilitate bench mounting.
Attach the saw to a level, horizontal bench or work table
using bolts (not supplied) though the fixing holes in the
saw base. (Fig. 3)
NOTE: If desired, you can mount the saw to a piece of
13 mm or thicker plywood which can then be clamped
to your work support or moved to other job sites and re-
clamped.
WARNING: Make sure that the mounting sur-
face is not warped as an uneven surface can cause
binding and inaccurate sawing.
TKN 80D • TKN 95D
4.7.2012 . 11:15:14 .