Quick Start Guide - nedis WIFIFNH20CWT Mode D'emploi

a

Quick start guide

Electric fan heater
For more information see the extended
manual online: ned.is/wififnh20cwt
Intended use
The Nedis WIFIFNH20CWT is an electric fan heater used for heating
rooms.
Any modification of the product may have consequences for safety,
warranty and proper functioning.
Main parts (image A)
1
Control panel
2
Air outlet
3
Handle
Safety instructions
WARNING
-
• Only use the product as described in this manual.
•
Any other use may cause fire, electric shock, and/or injury to
persons and may void the warranty.
•
Any use of not recommended attachment or accessory may
cause injury to persons, or damage.
• Do not use the product if a part is damaged or defective.
Replace a damaged or defective device immediately.
•
Do not disassemble or try to repair the product.
•
Do not drop the product and avoid bumping.
•
This product may only be serviced by a qualified technician for
maintenance to reduce the risk of electric shock.
• Make sure that the electrical supply in your area matches a
voltage of 220 – 240 VAC and a frequency of 50 Hz.
•
Make sure that no other high current appliances are plugged
into the same circuit with your product. Overloading may occur.
• Disconnect the product from the power outlet and other
equipment if problems occur.
•
Do not expose the product nor the cord to water, any other
liquid or moisture.
•
Do not use the product where splashing of water might occur
e.g. bathrooms, swimming pools or close to a washbowls.
• Fully extend the power cord and make sure the power cord does
not contact the product.
•
Do not cover the power cord by e.g. carpets, rugs or furniture.
•
Ensure people do not trip over the cord.
• Only plug the cable into a wall outlet. Do not use extension cords.
• Do not use the product when the cord or plug is damaged.
• Turn off the main power switch before unplugging the power cord.
•
Do not unplug the product by pulling on the cable. Always
grasp the plug and pull.
•
Do not let children play with parts of packaging such as plastic
bags, because of danger of suffocation.
• Close supervision is necessary when the product is used by or
near children, animals or infirm persons. Do not allow children
to play with it or touch it.
WIFIFNH20CWT
4
Air inlet grid
5
Power switch
6
Plug
•
Do not leave the product unattended when switched on.
•
Do not use the product in rooms where flammable liquids or
gases are used or stored.
• An area of one meter around the product has to be free from
animals and any combustible materials, such as curtains and
bedding or walls. Do not point the outlet at any of these.
•
Do not obstruct or cover the product's air inlet or outlet grid.
•
Do not place any objects on the product.
• Do not locate the product immediately below a power outlet.
• Do not move the product during operation.
•
After use only transport the product by using the handle.
•
Only handle the product with dry hands. Handling with wet
hands might cause an electric shock.
• Switch off and unplug the product when not in use or before
maintenance.
•
Do not pull the power cable over sharp edges.
Switch on the heater
1. Insert the plug into a power outlet.
2. Then turn on the main power switch A
Now the heater is in "stand-by" mode, with only the temperature
indicator shown.
Use the control panel (image B)
1
On / off button
2
Display
3
Low power indicator
4
Oscillation button
5
Mode indicator
6
Timer indicator
Stand-by
1
1. Press B to wake the product. B
1
2. Press B
again to change back to stand-by.
4 The fan will continue to turn for 30 seconds to cool down.
Low – high power
9
1. Press B
to switch between low power, high power or fan
only.
3
4 B
lights up for low power.
q
4 B lights up for high power.
Timer
7
1. Press B to activate the timer, B
4 The time will show at B
4 The time can be set between 1 to 8 hours.
7
2. Hold B to deactivate the timer.
Oscillation
4
1. Press B
to activate the oscillation.
4
2. Press B
again to deactivate the oscillation.
4
5
.
7
Timer button
8
Status indicator
9
Power button (low, high
or fan only)
10
High power indicator
11
Set temperature button
5 8
and B
will light up.
6
will light up.
5
.