Quick Start Guide - nedis COOL117CWT Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

a

Quick start guide

Air Cooler
For more information see the extended manual online:
ned.is/cool117cwt
Intended use
The Nedis COOL117CWT is an air cooler with a 6 L water tank
capacity.
The product is not intended for professional use.
This product can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the product in a safe
way and understand the hazards involved. Children shall not play
with the product. Cleaning and user maintenance shall not be done
by children without supervision.
Any modification of the product may have consequences for safety,
warranty and proper functioning.
Specifications
Product
Article number
Dimensions (l x w x h)
Weight
Power input
Power
Water tank capacity
Air volume
Fan speed
Ionizer function
Automatic air swing
Timer
Remote control
Main parts (image A)
1
Air outlet
Water level indicator
2
Power button
3
4
Swing button
Speed button
5
Timer button
6
7
Cool button
Ioniser button
8
Safety instructions
-
WARNING
• Ensure you have fully read and understood the instructions in this
document before you install or use the product. Keep the
packaging and this document for future reference.
• Only use the product as described in this document.
• Do not use the product if a part is damaged or defective. Replace a
damaged or defective product immediately.
• Do not drop the product and avoid bumping.
• This product may only be serviced by a qualified technician for
maintenance to reduce the risk of electric shock.
• Disconnect the product from the power source before service and
when replacing parts.
• Disconnect the product from the power source before removing
the fan guard.
COOL117CWT
Air Cooler
COOL117CWT
270 x 275 x 690 mm
5500 g
220 - 240 VAC ; 50 / 60 Hz
80 W
6 L
300 m3/h
Low / moderate / high
Yes
Yes
1 - 12 h
Yes
9
Particle filter
Honeycomb filter
q
Water tank lock
w
e
Water tank
Power cable
r
Ice packs
t
y
LED display
Installation
1. For optimal performance, place the product on a location that
complies with the following:
• Flat and stable surface.
• 50 - 60 cm free space around the product.
2. Close open doors and windows.
If you notice that the humidity level reaches 60% or above,
4
ventilate the room for optimal performance.
3. Plug the power cable A
Filling the water tank
-
Do not fill the water tank above the "max" indicator.
-
Do not use the product if the water level is below the "min"
indicator.
1. Open the water tank lock A
2. Slide out the water tank A
the "max" indicator.
3. Slide A
back into the product.
e
4. Close A
w
.
Using ice packs
The use of ice packs A
4
Fill A
t
with water until the water level is at the "max" indicator.
4
Add A
to A
t
e
if tap water does not provide enough cooling.
4
-
Make sure the water level is between "min" and "max" after
adding A
t
.
Using the product
1. Press A
3
to switch on the fan.
2. Press A
5
to set the fan speed.
A
indicates the current fan speed.
y
3. Press A
3
to switch off the fan.
Using the cooling function
• Press A
7
to activate or deactivate the cooling function.
A
y
lights up when the function is active.
For optimal performance, switch off the cooling function 15
4
minutes before switching off the fan.
Setting air flow direction
• Press A
to automatically swing the air flow from left to right.
4
A
y
lights up when the function is active.
• Use A
1
to set the vertical air flow direction.
Using the timer
• Press A
6
to set the timer.
• Press again to increase the timer up to 12 hours.
The product switches off after the set time has passed.
A
y
shows the selected time.
Using the ionizer
• Press A
8
to switch on the ionizer.
A
y
lights up when the function is active.
Maintaining the filter
Clean the honeycomb filter A
4
Let A
completely dry before storage to prevent molding.
4
q
Replace A
q
once a year or when the airflow is decreasing.
4
To buy new filters, see www.nedis.com, or contact the Nedis
4
B.V. service desk.
To clean A
q
:
1. Remove A
and A
9
q
2. Wash A
with water and soap.
q
3. Rinse A
q
with clean water.
4. Let A
q
dry.
5. Place back A
and A
q
4
r
into a power outlet.
.
w
e
and fill it with clean tap water up to
t
is optional.
q
every two months.
.
9
.

Publicité

Table des Matières
loading

Table des Matières