After Treating With Silk'n Freedom; Maintenance Of Silk'n Freedom; Cleaning Silk'n Freedom; Replacing The Lamp Cartridge - Home Skinovations Silk'n Freedom Démarrage Rapide

Moderate Pressure of the Treatment Surface – This is necessary and helpful for placement of adjacent pulses of
light, and is part of the unique safety feature of Silk'n Freedom.
A Sensation of Warmth and Tingling – During each pulse of light it is normal to feel a mild sensation of warmth
and tingling from the light energy.
Some Mild Red or Pink Color – During and just after your Silk'n Freedom session it is not uncommon to see some
very mild, pink-like color of the skin. This is usually most noticeable around the hairs themselves.
However if you see full redness of the skin, blistering or burns stop use of Silk'n Freedom immediately.

9.2. After treating with Silk'n Freedom

When Silk'n Freedom session has been completed turn Silk'n Freedom off by pressing the On/Stby Switch. All the
lit indicators will turn off and the STBY INDICATOR LIGHT will turn on (Be sure to remember the last energy level
setting you used, as it will not be restored when turning Silk'n Freedom on again.)
Unplug the ADAPTOR cord from the electrical outlet.
After each hair removal session it is recommended that you clean your Silk'n Freedom device, especially the
Treatment Surface (See: "Cleaning Silk'n Freedom").
After cleaning, it is recommended to store your Silk'n Freedom device in its original box, and keep it away from
water.
Skin care following hair removal session
Do not expose treated areas of skin to the sun. Be sure to carefully protect the treated
skin with sunscreen, throughout the hair removal period and for at least 2 weeks following
the last Silk'n Freedom session.
16

10. Maintenance of Silk'n Freedom

10.1. Cleaning Silk'n Freedom

After each hair removal session, it is recommended to clean your Silk'n Freedom device, and especially the Treatment
Surface.
Unplug Silk'n Freedom before cleaning.
Use a dry, clean cloth and a specially formulated cleaner for electronic equipment to gently wipe Silk'n Freedom
surface, and especially the Treatment Surface.
Never immerse Silk'n Freedom or any of its parts in water!

10.2. Replacing the Lamp Cartridge

The Silk'n Freedom DISPOSABLE LAMP CARTRIDGE can fire a pre-set and limited number of light pulses. Pulse
intensity is determined only according to the energy level setting of the device. There is no decrease of energy during
the usable lifetime of the LAMP CARTRIDGE.
When only 100 light pulses remain in the DISPOSABLE LAMP CARTRIDGE, the REPLACE CARTRIDGE INDICATOR
LIGHT on the CONTROL PANEL will start blinking, indicating that the DISPOSABLE LAMP CARTRIDGE should
soon be replaced.
This device has a cartridge with 300,000 light pulses so replacement cartridges should not be required.
As the number of light pulses in the DISPOSABLE LAMP CARTRIDGE further decreases, the REPLACE CARTRIDGE
INDICATOR LIGHT blinking will grow faster.
Once all the pulses in a DISPOSABLE LAMP CARTRIDGE have been used, the REPLACE CARTRIDGE INDICATOR
LIGHT will remain steadily on, indicating that further pulses cannot be emitted.
In order to continue the hair removal session, it will now be necessary to replace the DISPOSABLE LAMP CARTRIDGE.
Note: A DISPOSABLE LAMP CARTRIDGE should also be replaced if large spots appear
inside it or if its TREATMENT SURFACE is broken.
To replace a DISPOSABLE LAMP CARTRIDGE:
1. Press the ON/STBY SWITCH to turn Silk'n Freedom to Stby mode.
2. Unplug the power adaptor from the electrical outlet.
3. Grasp the used DISPOSABLE LAMP CARTRIDGE on both sides, pull it out of the socket and discard with normal trash.
4. Unwrap a new DISPOSABLE LAMP CARTRIDGE.
5. Push the new DISPOSABLE LAMP CARTRIDGE gently into place.
Note! After replacing the disposable lamp cartridge with a new one, always set the energy to be one level
lower than your normal setting. Raise the energy level back, only if you do not experience abnormal discomfort
during or after the treatment.
17