Publicité
Les langues disponibles
Les langues disponibles
air Supply
Tools of this class operate on a wide range of air pres sures. It is
recommended that air pres sure of these tools mea sures 90 PSI at the
tool while running free. Higher pres sure (over 90 psig; 6.2 bar) raises
performance beyond the rated capacity of the tool which will short en
tool life be c ause of faster wear and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or water in the air
line will cause damage to the tool. Drain the air tank daily. Clean the
air inlet filter screen on at least a weekly schedule. The rec om mend ed
hookup pro ce dure can be viewed in the above figure.
The air inlet used for con nect ing air supply, has stan dard 1/4" NPT .
Line pressure should be increased to compensate for unusually long
air hoses (over 25 feet). Minimum hose diameter should be 3/8" I.D.
and fittings should have the same inside di men sions and be tightly
secured.
Whip Hose
Do Not Install
Quick Coupling
Nipple
Here
Quick Coupler
Leader Hose
WarranTy
Matco warrants its air tools for a period of 1 year to the consumer. We
will repair any MT Series air tool covered under this warranty which
proves to be defective in material or workmanship during the warranty
period. In order to have your tool repaired, return the tool to either of the
Matco Authorized Warranty Centers listed below, freight prepaid. Please
include a copy of your proof of purchase and a brief description of the
problem. The tool will be inspected and if any part or parts are found to
be defective in material or workmanship, the tool will be repaired free
of charge and returned to you freight prepaid.
This warranty gives you specific rights. You may also have other rights
which vary from state to state.
The foregoing obligation is Matco's sole liability under this or any
implied warranty and under no circumstances shall Matco be liable for
any incidental or consequential damages.
note: Some states do not allow the exclusion or limitation of
incidental or consequential damages so the above limitation or
exclusion may not apply to you.
MT1840
MT1840 3/8" Mini Air Ratchet
FeatureS
•
Combines a great small tool with a 3/8" anvil for better versatility.
•
Patented, built-in grease fitting for greater durability and longer life.
•
Forged chrome, molly ratchet yoke for great durability and strength.
•
Very small head design, (1" wide) for great access almost anywhere.
•
Overall length of 6-5/8" for unmatched access in tight work spaces.
Air Supply
Filter
Nipple
Regulator
Oiler
Drain Daily
trOubleShOOting
Other factors outside the tool may cause loss of power or erratic
action. Reduced compressor output, ex ces sive drain on the air line,
moisture or restrictions in air pipes or the use of hose connections of
improper size or poor conditions may reduce air supply. Grit or gum
deposits in the tool may cut power and may be corrected by cleaning
the air strainer and flushing out the tool with gum solvent oil or an
equal mixture of SAE #10 and kerosene. If outside conditions are in
order and tool continues to perform erratically, disconnect tool from
hose and take tool to your nearest MATCO au tho rized service center.
lubricatiOn
Lubricate the air motor daily with quality air tool oil. If no air line oiler
is used, run a teaspoon of oil through the tool. The oil can be squirted
into the tool air inlet or into the hose at the nearest con nec tion to the
air supply, then run the tool. The amount of oil to be used is 1 ounce.
Overfilling will cause a re duc tion in the power of the tool. Grease fitting
on yoke occasionally to ensure proper lubrication of the ratchet
mechanism.
Matco air command
Tool repair sV
1330 Commerce Dr.
Stow, OH 44224
(800) 433-7098
discount Tool repair
3433 Losee Rd. #1
North Las Vegas, NV 89030
(702) 657-6570
3
Rev. 06/18/08
Publicité
