DWT OF-1050 NV Notice Originale page 26

placed behind the frame (tool operation shall not be
affected)�
• The machine shall be operated in rain or humid
environment. You shall not touch the power lines to
avoid fire or electric shock.
• Before the machine is removed from the work-
piece, you shall cut off power switch and com-
pletely stop the milling cutter.
• The hands shall always be far away from the ro-
tating parts. When the milling cutter is in contact with
the workpiece, you shall not make an attempt to start
the machine�
• After work, the switch shall be turned off first
and then lock knot of guide pillar shall be loosed
to make the machine return to original position.
Safety guidelines during
power tool operation
Before commencing operation
• During machining, do not place the workpiece on a
sturdy surface (concrete, steel, stone, etc�) - when the
router bit passes through the workpiece, you can dam-
age the router bit and lose control over the power tool�
• Use the router bits whose allowable rotary speed
does not exceed the rotary speed of the power tool
spindle� Observe manufacturer's recommendations
for router bits use� Do not use router bits that do not
conform to the specifications included in the user's
manual�
• Use only sharp nondefective router bits� Bended,
blunt or cracked router bits must be replaced�
• The router bit shank diameter must match precisely
with the internal diameter of the power tool collet�
• Never use the router bit if its cutting unit diameter
exceeds the diameter of the hole in the base plate�
• Remove all nails or any other metal objects from
blanks before cutting�
• When making cuts in walls or partitions, it is neces-
sary to find the location of hidden wiring, water-pipes
and gas pipes� Severe injuries may occur as a result of
damaging electric wiring or household utility lines�
During operation
• When turning the power on and during operation,
hold the power tool with both hands by both handles
and keep a steady position, which will allow you to
keep control over the power tool�
• Keep your hands at a safe distance from the rotat-
ing router bit� Remember that when machining a work-
piece, the router bit end occasionally protrudes beyond
the lower part of the workpiece and is not protected -
touching it may cause severe injuries� Never touch the
rotating router bit with your hands�
• Never start the machining until the router bit reaches
its full speed�
• Advance the router bit to the workpiece only with the
power tool turned on, otherwise the router bit may be
pinched in a workpiece, or a recoil and loss of control
over the power tool can occur�
• When processing small blanks, use clamping devic-
es. If the blanks are too small to be fixed properly - do
not process them�
• Never remove sawdust while the power tool motor
is running�
• Do not work materials containing asbestos� Asbes-
tos is considered carcinogenic�
• Avoid stopping an electric tool motor when loaded�
• Avoid overheating your power tool, when using it for
a long time�
• Never operate the power tool over your head level�
After finishing operation
• The power tool may be removed from the workplace
only after it is turned off and the router bit stops com-
pletely�
• Decelerating the router bit rotation by inertia using
the spindle keylock is strictly forbidden- this will put the
power tool out of operation and void your right to the
warranty service�
• During operation the router bit runs very hot - do not
touch it until it cools down�
• Cleaning of the workplace after work should be per-
formed by persons equipped with the aforesaid per-
sonal protection means�
Warning: the chemical substances con-
tained in dust generated in sanding,
cutting, sawing, grinding, drilling and
other construction industry activities
may result in cancer, congenital deficiency or be
harmful to the fertility. The ion of some chemical sub-
stances shall be:
• Before any repair and replacement work to the ma-
chine, the power plug must be pulled out firstly.
• The transparent two silicon oxide and other masonry
products in the wall bricks and cement; the chromium
arsenic (CCA) in wood with chemical treatment� The
harm degree of these substances shall depend on the
frequent degree of you carrying out these works� If you
want to reduce the contact with these chemical sub-
stances, please work in the place with ventilation and
you shall use the appliances with safety certificates
(such as the dust mask designed with tiny dust filter).
Notice the power voltage: in power connection, you
must confirm that if the power voltage is the same to
the voltage marked in the tool's data plate� If the power
voltage is higher than the appropriate voltage, the acci-
dents will be resulted to the operators, and at the same
time, the tool will be destroyed� Therefore, if the power
voltage has not been confirmed, then you shall never
plug in arbitrarily� On the contrary, when the power
voltage is lower than the required voltage, the motor
will be damaged�
Following symbols are used in the operation manual,
please remember their meanings� Correct interpreta-
tion of the symbols will allow correct and safe use of
the power tool�
Symbol
OF- ...
XX XXXXXXX
Ser.No.:
English
26
Symbols used in
the manual
Meaning
Serial number sticker:
OF ��� - model;
XX - date of manufacture;
XXXXXXX - serial number�