Publicité
Les langues disponibles
Les langues disponibles
Installation
• If you want to install the device on a surface, attach the two mounting angles to the housing
with the corresponding screws and screw the device onto the mounting surface.
Only use the screws included in delivery to install the mounting angle to the device.
Other (longer) screws can damage parts in the device.
• If you want to stand the device on a surface, stick the rubber feet included in delivery to the
base of the device.
Inserting/replacing the battery of the remote control
When using the device for the first time, the battery of the remote control may al-
ready be protected from discharging by an insulation film. Remove this film before
operation, where required, by pulling it out of the battery compartment of the remote
control.
• Release the safety catch and remove the battery holder on the back of the remote control.
• Insert a new 3 V Lithium button cell CR2025, with the correct polarity. The correct polarity is
indicated on the remote control.
• Close the battery compartment. The latch must snap audibly into place.
• If the remote control is no longer functioning properly, or the range decreases, the battery
is running out and must be replaced with a battery of the same type. Replace the battery as
described above.
Connecting inputs and outputs
• Connect the HDMI outputs on your playback device to the HDMI inputs (9) on the Quad
Multi-Viewer.
• Connect the HDMI input on your screen to the HDMI output (3) on the Quad Multi-Viewer.
All source devices must be set to the same image resolution.
Mains connection
The mains socket to which the power adapter is connected must be near the device
and easily accessible, so that the device can be quickly and easily isolated from the
mains power supply in the event of any fault.
Make sure that the voltage indicated on the power unit corresponds with the mains
voltage of your power supply. Never try to operate the power supply at a different
voltage.
Be careful when handling the power adapters and mains connectors. Mains voltage
may cause fatal electric shocks.
Do not leave the cables trailing free; route them in an orderly and professional man-
ner to prevent accidents.
• Connect the low-voltage plug of the enclosed power unit to the power supply connection (1)
on the Quad Multi-Viewer and tighten the locknut.
• Plug the power adapter into a wall socket.
• The display (2) lights up once the Quad Multi-Viewer is connected to the electricity supply.
• Once an active source is recognised, the display lights up for the corresponding HDMI input (8).
Operation
a) Device
• Press the MODE key (6) to select a display type on the screen. The display types now show
as available and can also be selected directly via the remote control.
• Press the AUDIO button (5) to select the input for sound reproduction. The chosen input
is displayed on the screen via a corresponding symbol. There is also an additional mode,
whereby all inputs are muted.
b) Remote control
Point the remote control at the IR receiver (7) to operate the controls.
Remote control function buttons
On/Off switch
Full screen display of Input 1/2/3/4
Display of Inputs 1 and 2 or 3 and 4 side by side
Display of all inputs at the same time next to/ under one another
H-form display of all inputs
Image display 1x large / 3x small in different channel configurations
Sound selection Input 1/2/3/4
Sound muting button
Button for changing screen resolution (720p <> 1080p)
No function
Software
• If you want to control the Quad Multi-Viewer via the RS232 interface, please download the
required software using this link: www.conrad.com/downloads. Follow the instructions on the
website.
• Make an interface cable by connecting the supplied adapter plug for the RS232 interface with
an RS232 cable as follows (the view refers to the connection side of the RS232 adapter plug:
RS232 Pin
Disposal
a) Product
Electronic devices are recyclable and do not belong in the household waste. Dispo-
se of an unserviceable product in accordance with the relevant statutory regulations.
Remove the battery if there is one inserted and dispose of it separately from the
product.
b) Batteries/rechargeable batteries
You as the ultimate consumer are legally obliged (Regulation on Spent Batteries)
to return all dead batteries and accumulators. Disposal in the household waste is
prohibited.
Batteries containing hazardous substances are labelled with the symbol shown to
indicate that disposal in household waste is forbidden. The symbols of the critical
heavy metals are: Cd = cadmium, Hg = mercury, Pb = lead (the marking can be seen
on the battery, e.g., underneath the refuse bin symbol shown on the left).
You can return your used batteries at collection points of your community at no cost or
wherever batteries are sold.
That way you fulfil your statutory obligations and contribute to the protection of the
environment.
Technical data
Operating voltage ......................... 12 V/DC (Quad Multi-Viewer)
......................................................
100-240 V/50/60 Hz (power unit)
Inputs and outputs ........................ 4 inputs / 1 output
Resolution (input) ......................... 480i/60 Hz / 480p/60 Hz
......................................................
576i/50 Hz / 576p/50 Hz
......................................................
720p/50/60 Hz
......................................................
1080i/50/60 Hz / 1080p/24/25/30/50/60 Hz
Resolution (output) ....................... 720p / 1080p
Interface for software .................... RS232
Dimensions ................................... 148.5 x 103 x 21.5 mm
Weight .......................................... 342 g
Operating conditions ..................... 0 to +70 °C / 10-85% rel. humidity
Storage conditions ........................ -10 to +80 °C / 5-90% rel. humidity
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2018 by Conrad Electronic SE.
RX GND TX
2 5 3
1642716_V1_0318_02_VTP_m_en
Publicité
