Hayward MaxFlo Serie Guide De L'utilisateur page 3

• •
•
warnInG
•
warnInG
F NF C 15-100
D DIN VDE 0100-702
A ÖVE 8001-4-702
E UNE 20460-7-702 1993, REBT ITC-BT-31 2002
IRL Normas de cableado + IS HD 384-7-702
I CEI 64-8/7
LUX 384-7.702 S2
NL NEN 1010-7-702
P RSIUEE
•
warnInG
The pump is to be supplied by an isolating transformer or supplied through a residual current device (rCD) having a rated
residual operating current not exceeding 30 ma.
•
warnInG
objects away from openings and moving parts.
•
warnInG
units use properly grounded outlet.
•
warnInG
as required by electrical codes.
•
warnInG
box. Be sure to check the electric connections are tight and sealed before powering up. replace all covers before operation.
•
warnInG
network and that the power supply cables matches the power and current of the pump.
•
warnInG
instructions can cause serious injury or death.
This document should be given to the owner of the swimming pool and must be kept by the owner in a safe place.
•
warnInG
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
•
warnInG
•
warnInG
persons in order to avoid a hazard.
•
warnInG
provide a full disconnection under overvoltage category III conditions must be incorporated in the fixed wiring in accordance
with the wiring rules.
•
warnInG
damaged. This can cause an electric shock. a damaged power cord or motor connection box must be replaced by a service
agent or a similarly qualified person immediately in order to avoid a hazard.
•
warnInG
drowning due to body entrapment on underwater drains. In some pool configuration, if a person's body covers the drain, the
person can be trapped by suction. Depending on your pool configuration, a svrs may be required to meet local requirements.
Page 2 of 5
instructions can result in serious injury or death.
– Disconnect the pump from the main power supply completely before servicing the pump or filter.
– all electrical connections must be done by a qualified electrician according to local electrical standard.
– Be certain the machine is only plugged into a protected 230 v outlet that is protected from short-circuits.
– Children should be supervised to ensure that they do not play with the appliance. Keep fingers and foreign
– motor must be suitably grounded. Connect ground wire to green grounding screw and for cord connected
– use a motor bonding lug to connect motor with other bonded parts using the appropriate size conductor
– when making these electrical connections, refer to the diagram given under the lid of the motor terminal
– make sure that the power supply voltage required by the motor corresponds to that of the distribution
– read and follow all instructions in this owner's manual and on the equipment. Failure to follow
– This appliance is not intended for use by persons (including children) with reduced physical, sensory or
– use only Genuine hayward replacement Parts.
– If the supply cord is damaged it must be replaced by the manufacturer, service agent, or similarly qualified
– For disconnection from main power supply an external switch having a contact separation in all poles that
– Do not operate the swimming pool pump if the power cord or the housing of the motor connection box is
– This pool motor is noT equipped with a safety vacuum release system (svrs). svrs helps prevent
use onlY haYwarD GenuIne rePlaCemenT ParTs
warnInG: electrical hazard. Failure to follow
For use wITh swImmInG Pools
GB BS7671:1992
EW EVHS-HD 384-7-702
H MSZ 2364-702:1994 / MSZ 10-533 1/1990
M MSA HD 384-7-702.S2
PL PN-IEC 60364-7-702:1999
CZ CSN 33 2000 7-702
SK STN 33 2000-7-702
SLO SIST HD 384-7-702.S2
TR TS IEC 60364-7-702
pump Rev. D