Publicité
Les langues disponibles
Les langues disponibles
the power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR JIG SAWS
•
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord (cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock)
•
Use clamps or another practical way to secure and
support the workpiece to a stable platform (holding
the workpiece by hand or against your body leaves it
unstable and may lead to loss of control)
GENERAL
•
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
•
Do not work materials containing asbestos (asbestos
is considered carcinogenic)
•
This tool should not be used by people under the age of
16 years
•
The noise level when working can exceed 85 dB(A); wear
ear protection
•
Wear protective goggles when working with materials
which produce chips
Dust from material such as paint containing lead, some
•
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
•
Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
•
Follow the dust-related national requirements for the
materials you want to work with
•
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
•
Always disconnect plug from power source before
making any adjustment or changing any accessory
BEFORE USE
•
Remove all obstacles on top of as well as underneath the
cutting path before you start cutting
•
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
DURING USE
•
Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
•
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
•
Never use the tool when the cord is damaged; it must be
replaced by a specially prepared cord available through
the service organization.
•
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
•
Keep hands away from the saw blade while the tool is
in use
ACCESSORIES
•
SKIL can assure flawless functioning of the tool only
when original accessories are used
•
Do not use a saw blade which is cracked, deformed or
dull
AFTER USE
•
When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Double insulation (no earth wire required)
5 Do not dispose of electric tools and batteries together
with household waste material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
•
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
•
If for any reason the old plug is cut off the cord of this tool,
it must be disposed of safely and not left unattended
USE
•
On/off 6
•
Switch locking for continuous use 7
•
Changing saw blades 8
! insert blade to full depth with teeth facing forward
9
- tool accepts most commonly available T-shank and
U-shank blades
•
Sawing at 45° q
•
Adjusting sawing speed to material used w
- if the tool does not run with wheel C in position 1, select
a higher sawing speed and lower the sawing speed
while the tool runs
•
Dust suction e
- connect vacuum cleaner adapter E to foot
- connect vacuum cleaner hose to vacuum cleaner
adapter E
! do not use vacuum cleaner when cutting metal
12
Publicité
