Assembling The Handlebar Upper Section (Illustration E1 ); Assemble The Collecting Sack And Hang It Onto The Mower (Illustration Q1 + R1 + S1 ); Adjusting The Cutting Height (Illustration I ); Before Using The Lawnmower For The First Time - Sabo 32-EL Livret D'entretien

Assembling the handlebar upper section (Illustration E1 )

– The safety grip for motor is pre-assembled on the upper handle and the cable to
the electric motor is attached here.
– Fit the handlebar upper section to the lower section at right and left, so that the
attachment holes of both sections are in alignment.
– Insert the flat-head screw inwards on the left hand side, and the cable guide
inwards on the right hand side and screw both handlebar sections together on the
inside using a washer and a wing-nut.
– Place the cable into the cable guide. This prevents trapping of the cable when
folding the handlebar.
– Attach the cable to the lower handlebar section using the cable tie from the
toolbag. When folding the upper handlebar section, ensure that the cable is not
trapped.
Assemble the collecting sack and hang it onto the mower
(Illustration Q1 + R1 + S1 )
– Turn the chute (1) outwards and push fully down Q1 .
– First insert the grass bag frame with the clip forward into the grass bag. Align the
upper seams of the bag with the clip.
– Press the retaining profiles of the collecting sack onto the bars of the collecting
sack frame R1 .
– Press the chute (1) on to the collecting sack frame from above Q1 .
– Open the ejection flap of the mower upwards.
– Pick up the collecting sack by the carrying strap, place the chute (1) at the
collecting sack opening into the ejection flap and hang it in the mower casing with
its two side hooks upwards S1 .
– Attach ejection flap to collector.

Adjusting the cutting height (Illustration I )

The desired cutting height is set at the front and rear with the respective adjusting
levers on the left side of the mower.
– Pull lever to the side to release from the notch, adjust to required position and
reinsert in notch.
– All wheels must be positioned at the same height.
IMPORTANT
Mowing at the lowest cutting height should only be carried out on level and plane
lawns!
Please observe that the lower cutting height settings may only be used for
optimal conditions. If you select cutting height that is too low, the turf can be
damaged and under certain circumstances it can even be destroyed.
Besides the cutting height, also the moving speed influences the cutting pattern
and collection result. Adapt the cutting height and moving speed to the grass
height to be cut.

9 BEFORE USING THE LAWNMOWER FOR THE FIRST TIME

Check all screw connections for a tight fit. Tighten the screws if necessary. Attachment
of the cutter bar must be checked in particular (refer here to the chapter "Cutter bar
care").
The blade attachment screw must always be tightened by an authorised workshop
since an insulation protection test always has to be carried out after repairs or
maintenance work on insulation parts (e.g. blade screw) in accordance with the
applicable standard DIN EN 60335.
The lawn mower is equipped with a motor stop device.
Before using the equipment for the first time, make sure that the motor stop safety
control bar is working perfectly. When the control bar is released, the motor and cutter
bar must come to a standstill within three seconds.
After release, the bar must always return to the position shown in the "component
description" diagram.
If this is not the case, it must be checked immediately by an authorised workshop.
Risk of injury!
If the blade run-on time is longer, stop using the equipment and take it to an authorised
workshop.
Measuring run-on time
After the electric motor has been started, the blade rotates and a wind-like noise can be
heard.
Safety instruction!
See table for explanation of symbols page 3
Safety instruction!
See table for explanation of symbols page 3
The run-on time corresponds to the duration of the wind-like noise after the electric
motor has been switched off, it can be measured using a stopwatch.
Machine safety and protective devices must not be manipulated or disabled!
Make sure that all protective devices have been attached properly and are not
damaged.

10 STARTING THE MACHINE

IMPORTANT
If the unit is to be operated via a generator, an authorised specialist workshop
should first be consulted with regard to a suitable generator.

Attaching the connecting cable (Illustration C2 )

NOTE
In order to guarantee the proper and safe operation of the garden equipment, a
connection cable of the minimum quality H05 RN-F (alternatively H05 VV-F) in
accordance with DIN/VDE 0282/4 with a cross-section of 3 x 1.5 mm² and a
connection plug made of or covered with rubber in accordance with DIN/VDE
0620-2-1 are required. Connection must be to a CEE 7/4 socket 230 V AC, slow-
blow 16 A fuse.
When a childproof cable is used, care must be taken that the fuse works perfectly
(smoothly) as otherwise the device connection plug could become damaged.
– Plug the cable into the switch/plug combination on the upper handle.
– Only then should the connecting cable be connected to the mains.
– When removing the cable always disconnect the cable plug from the mains first.
Attaching the connecting cable to the strain relief fitting
(Illustration D2 )
ATTENTION
The unit may not be used without the cable relief in order to prevent damages to
the switch/plug combination and to the cable. The cable must be hung in the
cable relief on the unit to ensure that it is fixed safely. This prevents the cable
socket from being pulled off the unit. Moreover, the cable aligns itself
automatically on the other side when cornering.
– Form a semi-circular loop in the cable, keep a distance of approx. 80 cm from the
connection cable coupling.
– Insert the cable from the bottom into the cable relief and loop it around the
fastening post.
– Hold the cable by both ends and pull it firmly into the cable relief.

Starting the motor (Illustration A2 )

Only start the engine when you are standing behind the mower.
Always place the mower on a level area which is not covered with high grass (if the
grass is too high it will block the cutter bar start-up and make starting the mower more
difficult). When the engine is started, the machine must not be tilted on end, if
necessary it must be tilted by pressing the guide bar down so that the cutting tool is
pointing in the direction away from the user, but only as far as absolutely necessary. As
long as the mower has not been lowered to the ground again, both your hands must be
on the top part of the bar.
– To switch on the motor, first press and hold the red button.
– With the other hand, pull the safety grip on the upper handlebar section. The grip
must be held in this position during operation.
– The red button can then be released.
IMPORTANT
If the motor does not start 5 seconds after the unit is started, then
1. Let go of the switch holder
2. Pull the plug!
3. Check the power cable
4. Check the power supply at the building (fuse)
5. Check the unit for blockages in the mowing chamber
6 Get it checked by an authorised specialist workshop.

11 SWITCHING OFF THE MOTOR (ILLUSTRATION F )

To switch off the motor, release the safety grip. The motor will be switched off and the
automatic blade brake stops the blade within 3 seconds.
6
Safety instruction!
See table for explanation of symbols page 3