Publicité
Les langues disponibles
Les langues disponibles
Assembly / installation
First of all, you should check whether all the
parts have been supplied by referring to the
summary on the left-hand side of the folder.
1. Turn the base upside down. Screw the feet
or wheels onto the legs and attach these to the
base. Use 1 screw for each leg.
2. Attach all the plastic corner attachments to
the base.
3. Lay out the support sections of the bed in
the correct order.
4. Position the base in such a way on the
sections that the section attachment points are
exactly above the corner attachments. Make
sure that no cables get caught.
5. Secure the base to the support sections,
placing the 16 screws through the corner at-
tachment points. Fasten the 4 screws on each
section by hand before tightening.
Pull the leads from the massage motors
through the cable ducts to the control unit at
the foot end.
Make sure the leads with the coloured strips
(the massage motor and air-conditioning leads)
are linked to the control unit cables which have
the same strips with colour codes.
6. The storage pouch can be attached to either
one of the sides of section 1 using 2 screws.
You can decide which side yourself.
7. Place the mattress and the top mattress on
the support sections. Now you can plug the
bed into the mains.
8. Connect the network adapter to the leads
poking out of the cable guide in the frame at the
head end. Then insert the plug into the socket.
9. When you use this function for the first time,
allow the head and end to raise gradually, after
activating the bed's remote control, and check
whether the massage or the lighting leads are
not pulled too tight. Keep moving the bed until
it has gone as far as it can.
6
Introduction
Congratulations on the purchase of your Jensen Dynamique adjustable
bed. We hope that it gives you many years of comfortable days and
nights. During the development of the Jensen Dynamique, special
attention was paid to ensuring that it is simple and safe to use. The
advanced technical features can be operated simply and smartly using
the handy remotecontrol and we recommend that you read on to
familiarise yourself with its use.
Guarantee
We provide a 5 year guarantee based on normal use. The invoice on
which the date of purchase is stated serves as a certificate of
guarantee. In the event of any faults or malfunctions, please
contact the store from which you purchased the bed.
Using the remote control
Insert the batteries (2 x AAA) into the remote control. You can only control the bed after the
remote control has been activated (see 'Activate the remote control').
The remote control can control the movement of the bed directly via the joystick if you keep
it vertical, with the display facing downwards.
If the display is pointing upwards, you will be able to use the menus with the joystick.
Move the joystick to the side to view the clock.
Press the joystick to view the menu. Use the joystick to move the marker to the desired
function and then press it. Set the desired functions. Deactivate the selected functions by
pressing the joystick twice or by setting them to zero.
If not used, the display will switch to energy saving mode after 15 seconds.
Activating the remote control
Activate the remote control for the right bed by pressing the button on the control unit under
the bed (see illus. 6). Keep this button pressed until it emits a double audible signal and then
release. Keep the remote control vertical, with the display facing down and move the joystick
to the left or the right to synchronise the remote control with the control unit.
The remote control has now been activated in conjunction with the control unit and the
electric motor under the bed.
NOTE: When you move the remote control to the left or right to connect it to the control unit,
it is important that you hold it upside down, that is with the display facing downwards and
with the joystick facing upwards. Go to the clock menu and scroll down with the joystick
until you reach the lowest field. Make sure the number 1 is shown in the display (address 1).
If this is not the case, click the field and then select the number 1.
Synchronising two beds (double bed)
First press the RED button on the control unit on bed number 1 until you hear two peeps
and then release the button.
Then keep the RED button on the control unit of bed number 2 pressed until you hear four
peeps (2 x 2) and then release the button.
Make sure you keep the remote control vertical with the display facing downwards, and that
the remote control is set to address number 1 (see NOTE to Activating the remote control).
Then move the joystick on the remote control for bed number 1 to the right, to the left, up
and down (keep pressing the joystick until the RED lamp on the control unit goes out).
Select bed number 2 on the remote control and in the menu select the address 'NEW'.
Follow the instructions shown in the display. While the text is active, briefly press the RED
button on the control unit of bed number 2 and then release again.
The beds are now synchronised on the remote control. Then set the address to '1+2' on
both remote controls if you want both beds to move in parallel.
NB: Only the movements of the beds can be synchronised.
NOTE: If, after the setting has been changed, the beds can be controlled in parallel but are
not in similar positions, lower the beds to get them parallel.
Lower bed in the event of a power failure
In the event of a power failure you can lower the bed by pressing the red button on the con-
trol unit and by keeping it pressed until it emits an audible signal. However, you must have
fitted two 9 volt batteries into the bed's drive box. If you use this function, you must replace
the batteries to ensure that the function will operate again should another power cut occur.
NOTE: The emergency function for lowering the bed can also be used without a power
failure having occurred. This can be handy of you have lost the remote control. If no power
failure has occurred, no charge from the batteries will be used.
Publicité
