Starmix GS Serie Notice D'utilisation page 10

Pumpsauger RS,TS, S.6-83
GB
I. Model GS/HS PA-1455 (without tilt trolley)
Mount the wheels on the trolley crossbar.
[Tighten] wheels with fastener in front Z.
II. Mount the run-off angle A on pump B/1.
Remove the lock S on the reflux valve B/2.
Loosen the run-off angle A B/3, B/4.
The reflux valve has to be mounted.
1. Mounting the tank with the pump
1.1. Insert the pump into the tank.
1.2. Screw the run-off angle A onto the tank thread
sleeve B (I).
1.3. Fasten the pump with the cable binder D on the
inside of the tank (I).
1.3.1. Remove the blind plug H and blind coupling G
refer to routine 1.3.1. a–d.
1.4. Press out the cable stopper J from the cable outlet C.
Lead the connecting cables for the pump through the
cable outlet C.
1.5. Put the cable stopper J over the pump cables on the
outside, push forward to the tank and press firmly into
the cable outlet C (I).
1.6. Connect the vacuum hose E and runoff hose F to
the tank.
1.7. Insert the connecting cables of the pump into the
socket K on the vacuum cleaner.
2. Retrofitting the pump vacuum cleaner/water
vacuum cleaner to a wet/dry vacuum cleaner
2.1. Remove the plug to the pump on the vacuum head.
2.2. Disassemble the cable stopper from the flange 1 + 1'
and pull the connecting cables of the pump through
flange 2 (II).
2.3. Loosen the cable binder D (II).
2.4. Unscrew the run-off angle A from the thread sleeve B (II).
2.5. Take the pump from the tank.
2.6. Firmly press the cable stopper J into the cable outlet
C again.
2.7. Press the blind plug H into cable stopper J to the catch.
2.8. Screw the blind coupling G on the runoff opening M.
You can now use the vacuum cleaner as a
conventional wet/dry vacuum cleaner
26.07.2007 12:22 Uhr
3.1. Remove the folded filter cartridge.
3.2. Carefully pull the blue foam filter over the filter basket.
3.3. Lead the runoff hose F into a water drain/gully hole
3.4. Plug the connecting cables of the pump into the
3.5. Turn on the vacuum cleaner by turning the rotating
3.6. Suction water with the vacuum hose E (and any
3.7. There is a certain amount of water left in the
3.8. If you want to separate course dirt (grain size
3.9. If you want to separate fine dirt (grain size < 0.5 mm)
Seite 9
3. Operating the pump vacuum cleaner
Also refer to the instructions for use for the wet/dry
vacuum cleaner.
– unlock the bayonet seal on the underside of the filter.
– remove the folded filter downward from the filter
basket.
Refer to Item 5.2 of the operating instructions for
the HS vacuum cleaner.
or a suitable area outside.
vacuum cleaner socket K.
When the pump is plugged in, the pump carries
out a brief self-test.
switch to ››I‹‹.
mounted accessories).
The pump automatically pumps the suctioned water
off over the runoff hose F with a built-in level switch
when it reaches a certain water level.
tank for technical reasons after completing
water vacuuming.
You can
a) empty all of this residual water by spilling it off, or
b) remove some of this residual water from the tank by
repeatedly pulling out and inserting the pump power
plug on the vacuum head.
≥ 0.5 mm) from water (for instance, when cleaning
ponds including thread algae), we recommend using the
supplied FSN 80 filter sack (424071).
from water, we recommend using the NFB wet
filter bag (420592).
The maximum pump passage size = grain size
10 mm when vacuuming without these two filter
systems.
The pump can get clogged due to thread algae. Refer
to 4.4 for cleaning.
9