STERWINS UP20 Notice De Montage, Utilisation Et Entretien page 166

FR 2.5 ELECTRICAL SAFETY
A ) POWER TOOL PLUGS MUST MATCH THE OUTLET. NEVER MODIFY THE
PLUG IN ANY WAY. DO NOT USE ANY ADAPTER PLUGS WITH EARTHED
ES
(GROUNDED) POWER TOOLS. UNMODIFIED PLUGS AND MATCHING OUTLETS
WILL REDUCE RISK OF ELECTRIC SHOCK.
B ) AVOID BODY CONTACT WITH EARTHED OR GROUNDED SURFACES,
PT
SUCH AS PIPES, RADIATORS, RANGES AND REFRIGERATORS. THERE IS
AN INCREASED RISK OF ELECTRIC SHOCK IF YOUR BODY IS EARTHED OR
GROUNDED.
IT
C ) DO NOT EXPOSE POWER TOOLS TO RAIN OR WET CONDITIONS. WATER
ENTERING A POWER TOOL WILL INCREASE THE RISK OF ELECTRIC SHOCK.
EL
2.6 PERSONAL SAFETY
A ) STAY ALERT, WATCH WHAT YOU ARE DOING AND USE COMMON SENSE
PL
WHEN OPERATING A POWER TOOL. DO NOT USE A POWER TOOL WHILE
YOU ARE TIRED OR UNDER THE INFLUENCE OF DRUGS, ALCOHOL OR
MEDICATION. A MOMENT OF INATTENTION WHILE OPERATING POWER TOOLS
RU
MAY RESULT IN SERIOUS PERSONAL INJURY.
B ) USE PERSONAL PROTECTIVE EQUIPMENT. ALWAYS WEAR EYE
PROTECTION. PROTECTIVE EQUIPMENT SUCH AS A DUST MASK, NON-SKID
KZ
SAFETY SHOES, HARD HAT OR HEARING PROTECTION USED FOR APPROPRIATE
CONDITIONS WILL REDUCE PERSONAL INJURIES.
UA
C ) PREVENT UNINTENTIONAL STARTING. ENSURE THE SWITCH IS IN
THE OFF-POSITION BEFORE CONNECTING TO POWER SOURCE AND/OR
BATTERY PACK, PICKING UP OR CARRYING THE TOOL. CARRYING POWER
RO
TOOLS WITH YOUR FINGER ON THE SWITCH OR ENERGISING POWER TOOLS
THAT HAVE THE SWITCH ON INVITES ACCIDENTS.
D ) REMOVE ANY ADJUSTING KEY OR WRENCH BEFORE TURNING THE
EN
POWER TOOL ON. A WRENCH OR A KEY LEFT ATTACHED TO A ROTATING PART
OF THE POWER TOOL MAY RESULT IN PERSONAL INJURY.
2.7 POWER TOOL USE AND CARE
A ) DO NOT FORCE THE POWER TOOL. USE THE CORRECT POWER TOOL FOR
YOUR APPLICATION. THE CORRECT POWER TOOL WILL DO THE JOB BETTER
AND SAFER AT THE RATE FOR WHICH IT WAS DESIGNED..
B ) DO NOT USE THE POWER TOOL IF THE SWITCH DOES NOT TURN IT
ON AND OFF. ANY POWER TOOL THAT CANNOT BE CONTROLLED WITH THE
SWITCH IS DANGEROUS AND MUST BE REPAIRED.
D ) DO NOT ABUSE THE CORD. NEVER USE THE CORD FOR CARRYING,
PULLING OR UNPLUGGING THE POWER TOOL. KEEP CORD AWAY FROM
HEAT, OIL, SHARP EDGES OR MOVING PARTS. DAMAGED OR ENTANGLED
CORDS INCREASE THE RISK OF ELECTRIC SHOCK.
E ) WHEN OPERATING A POWER TOOL OUTDOORS, USE AN EXTENSION
CORD SUITABLE FOR OUTDOOR USE. USE OF A CORD SUITABLE FOR OUTDOOR
USE REDUCES THE RISK OF ELECTRIC SHOCK.
F ) IF OPERATING A POWER TOOL IN A DAMP LOCATION IS UNAVOIDABLE,
USE A RESIDUAL CURRENT DEVICE (RCD) PROTECTED SUPPLY. USE OF AN
RCD REDUCES THE RISK OF ELECTRIC SHOCK.
E ) DO NOT OVERREACH. KEEP PROPER FOOTING AND BALANCE AT
ALL TIMES. THIS ENABLES BETTER CONTROL OF THE POWER TOOL IN
UNEXPECTED SITUATIONS.
F ) DRESS PROPERLY. DO NOT WEAR LOOSE CLOTHING OR JEWELLERY.
KEEP YOUR HAIR AND CLOTHING AWAY FROM MOVING PARTS. LOOSE
CLOTHES, JEWELLERY OR LONG HAIR CAN BE CAUGHT IN MOVING PARTS.
G ) IF DEVICES ARE PROVIDED FOR THE CONNECTION OF DUST
EXTRACTION AND COLLECTION FACILITIES, ENSURE THESE ARE
CONNECTED AND PROPERLY USED. USE OF DUST COLLECTION CAN REDUCE
DUST-RELATED HAZARDS.
H ) DO NOT LET FAMILIARITY GAINED FROM FREQUENT USE OF TOOLS
ALLOW YOU TO BECOME COMPLACENT AND IGNORE TOOL SAFETY
PRINCIPLES. A CARELESS ACTION CAN CAUSE SEVERE INJURY WITHIN A
FRACTION OF A SECOND.
C ) DISCONNECT THE PLUG FROM THE POWER SOURCE AND/OR REMOVE
THE BATTERY PACK, IF DETACHABLE, FROM THE POWER TOOL BEFORE
MAKING ANY ADJUSTMENTS, CHANGING ACCESSORIES, OR STORING
POWER TOOLS. SUCH PREVENTIVE SAFETY MEASURES REDUCE THE RISK OF
STARTING THE POWER TOOL ACCIDENTALLY.
D ) STORE IDLE POWER TOOLS OUT OF THE REACH OF CHILDREN AND DO
NOT ALLOW PERSONS UNFAMILIAR WITH THE POWER TOOL OR THESE
166