Before Starting The Equipment - EINHELL TE-TC 920 UL Instructions D'origine

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
The equipment has to be set up where it can
stand securely.
•
All covers and safety devices must be cor-
rectly attached before the machine is used for
the first time.
•
The cutting wheel must rotate smoothly.
Unfolding the base frame (Fig. 2)
To set up the equipment on its feet (1), press the
latching button (a) and lower the respective feet
(1) until they latch in the intended position. To fold
up the feet (1), proceed in reverse order.
Fitting the cooling water pump (Fig. 4A - 4C)
•
Place the cooling water pump (13) - with the
suction cups pointing down - into the contai-
ner (a).
•
Then fasten the hose to the intended posi-
tions as shown in Fig. 4B and 4C.
Notice!
To guarantee proper operation, the cooling water
hose (14) must not be kinked during installation.
Danger!
It must be impossible for the cable and the coo-
ling water hose to get into the cutting area.
Fitting the handle (Fig. 5)
Fit the handle (9) with the screws (a) as shown in
Fig. 5.
Fitting the side tables (Fig. 6)
Fit the side tables (23) as shown in Fig. 6.
6. Operation
6.1 ON/OFF switch (Fig. 3/4A)
•
To switch on, press the "I" on the ON/OFF
switch (16).
•
Before you begin cutting, wait until the cutting
wheel has reached maximum speed and the
cooling water pump (13) has started supply-
ing the cutting wheel with water.
Anl_TE_TC_920_UL_SPK9.indb 24 Anl_TE_TC_920_UL_SPK9.indb 24
GB
•
To switch off, press the "0" on the switch (16).
6.2 Fitting the transport aids (Fig. 7 - 9)
•
Fit the transport wheels (19), the parking foot
(20) and the transport handle (18) as shown
in Figs. 7/8/9.
6.3 Fitting the stop rail and the angle stop
(Fig. 10)
•
First push the stop rail (6) onto the guides (a)
as shown and fasten.
•
Then you can push the angle stop (5) into the
guide (b) and fasten in any position.
6.4 Making 90° cuts (Fig. 11/12)
•
Slacken the handle screw (24) and push the
angle stop (5) into the required position and
set the angle to 0° degrees, then tighten the
handle screw (24) again in order to secure
the angle stop (5).
•
Then slacken the clamping screw (12) and
push it to the required position.
•
You can now move the machine head by the
handle (9) to the rear.
•
Place a tile against the stop rail (6) and the
angle stop (5).
•
Switch on the machine.
•
Notice! Wait until the cooling water has
reached the cutting wheel (2).
•
Move the machine head by the handle (9)
slowly and smoothly forward through the tile.
6.5 45° Diagonal cut (Fig. 11/13)
•
Set the angle stop (5) to 45°.
•
Cut as described in 6.4.
6.6 45° Lengthwise cut, "jolly cut" (Fig.14/15)
•
Slacken the clamping screw (10).
•
Tilt the guide rail (7) to the left to 45° on the
angle scale (17).
•
Retighten the clamping screw (10).
•
Make the cut as described in 6.4.
6.7 Changing the diamond cutting wheel
(Fig. 16A-16B)
•
Pull out the power plug!
•
Remove the screw (25).
•
Swing up the cutting wheel guard (8).
•
Place the wrench (26) on the motor shaft and
hold.
•
Using the wrench (27), loosen the flange nut
in the direction of rotation of the cutting wheel
(2). (Caution: Left-hand thread.)
•
Remove the outer flange (28) and the cutting
wheel (2).
- 24 -
24.01.2022 08:53:16 24.01.2022 08:53:16