Installation; Mounting; Opening The Device/Electrical Connection; Cable Entry (Kle) - Cooper Crouse-Hinds CEAG GHG 516 Mode D'emploi

Fig. 1 Switching operation
Fig. 2
3 3 3 3 3
2 2 2 2 2
4 4 4 4 4
Fig. 3
Item 1
Item 2
Fig. 4
View 1
PE L1 N
Item 2 Item 1
Explosion protected plug and socket system
16A, GHG 516
In the open air, the plugs must be kept with the
plug opening (pin side) pointing downwards or
be closed with protective plug caps available
as an optional extra (see general catalogue).
The user alone is r The user alone is responsible for the The user alone is r
The user alone is r The user alone is r
appropriate use of this plug and socket appr appr appr appr opriate use of this plug and socket opriate use of this plug and socket opriate use of this plug and socket opriate use of this plug and socket
system in consideration of the basic system in consideration of the basic system in consideration of the basic system in consideration of the basic system in consideration of the basic
conditions existing at the plant (see technical conditions existing at the plant (see technical conditions existing at the plant (see technical
conditions existing at the plant (see technical conditions existing at the plant (see technical
data). data). data). data). data).
After a short in the cir After a short in the cir
After a short in the circuit, the functioning of After a short in the cir After a short in the cir
the plug and socket system and of the plugs the plug and socket system and of the plugs the plug and socket system and of the plugs
the plug and socket system and of the plugs the plug and socket system and of the plugs
has to be checked. has to be checked. has to be checked. has to be checked. has to be checked.
Since the switch contacts can no mor Since the switch contacts can no mor
Since the switch contacts can no mor Since the switch contacts can no mor Since the switch contacts can no more be
checked because of the flameproof enclosur checked because of the flamepr checked because of the flamepr
checked because of the flamepr checked because of the flamepr
the complete switch insert (flange socket) will the complete switch insert (flange socket) will the complete switch insert (flange socket) will the complete switch insert (flange socket) will the complete switch insert (flange socket) will
have to have to be r be r
have to be r have to have to be replaced after r be r
cir circuits. cir cir cir cuits. cuits. cuits. cuits.
6

Installation

For the mounting and operation, the
respective national regulations (e. g. Betr.Si.V.,
equipment safety law for Germany) as well as
the general rules of engineering will have to
be observed.
6.1

Mounting

The wall sockets can be mounted without
opening their enclosure.
In case the wall sockets are mounted directly
onto the wall, they may rest evenly only at the
6 6 6 6 6
respective fastening points. The chosen screw
shall match the fastening hole (see dimensio-
nal drawing) and it must not damage the hole
(e. g. use of a washer). The device shall be
5
fastened diagonally with at least 2 screws.
The wall sockets, flange sockets and
couplers shall be mounted so that the plug
hole points downwards (fig. 2).
Item 3
The wall sockets can be clipped onto the
COOPER CROUSE-HINDS / CEAG mounting
plate size 4. They are laterally pushed into the
View 2
guiding groove on the left-hand side of the
mounting plate.
The respective mounting instructions will have
to be observed.
A A A A A
A A A A A
Fastening point A
16A socket 3-pol.
esponsible for the esponsible for the esponsible for the
esponsible for the
cuit, the functioning of cuit, the functioning of
cuit, the functioning of cuit, the functioning of
e be e be
e be e be
oof enclosure, e, e, e, e, oof enclosur oof enclosur
oof enclosur
eplaced after r eplaced after r epeated short epeated short
eplaced after r eplaced after repeated short epeated short epeated short
A A A A A B B B B B
A A A A A
B B B B B
Fastening point B
16A socket 4,5-pol.
6.2 Opening the device/
Electrical connection
The electrical connection of the device may
only be carried out by electric trained staff.
The insulation of the conductors shall
reach up to the terminal. The conductor
itself shall not be damaged.
Taking into account the respective regulations,
the properly bared conductors of the cables
shall be connected.
The plug insert (item 2, fig. 4) is removed from the
pin bushing (item 1, fig. 4), after the fastening
screws (item 3, fig. 3) have been unscrewed.
Thereafter, the plug insert can be connected to the
connections of the plug pins (see view 1, fig. 4).
Attention: When the fastening screws (item 3, fig.
3) get lost, they will have to be replaced by similar
screws or to be ordered directly from the
manufacturer.
Assembly is made in inverse order, after the
cable has been connected.
The connectible min. and max. conductor
cross-sections shall be observed (see
technical data).
All screws and/or nuts of the supply terminals,
also of those remaining vacant, shall be tightened
down.
The conductors shall be connected with The conductors shall be connected with The conductors shall be connected with
The conductors shall be connected with The conductors shall be connected with
special car special car special car special care in or special car e in or e in or e in or e in order to maintain the der to maintain the der to maintain the der to maintain the der to maintain the
explosion category explosion category. . . . . explosion category
explosion category explosion category
The supply terminals are designed for the
connection of copper conductors. If multi- or
fine-wire connecting cables are used, the wire
ends will have to be handled in acc. with the
applicable national and international rules (e.g.
use of sleeves for strands).
6.3 Cable entries (KLE);
blanking plugs
6.3.1 Socket
Generally, only certified cable entries and
blanking plugs are permitted for use.
Flexible cables shall be used with trumpet-
shaped cable glands or other suitable
entries with additional pull-relief.
When using cable entries with a lower IP
protection than that which applies to the
B B B B B
device (see page 3, technical data), the IP
protection of the whole device will be
reduced.
The mounting directives applicable to the
cable entries used shall be observed.
Unused holes shall be closed with a certified
B B B B B
blanking plug in order to establish the
minimum protection category. In case of
sealing inserts that are cut out, it shall be
ensured that the insert is properly adapted to the
cable diameter.
COOPER Crouse-Hinds GmbH
9 9 9 9 9