Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
the end user to replace it if needed. To replace the rechargeable battery pack,
carefully follow the instructions listed below:
WARNING: TO PREVENT IGNITION OF A HAZARDOUS ATMOSPHERE, DO
NOT OPEN THE LENS BEZEL IN THE HAZARDOUS ENVIRONMENT. THIS
TASK MUST ONLY BE PERFORMED IN AN AREA KNOWN TO BE NON-
HAZARDOUS.
WARNING: WHEN EXCHANGING THE RECHARGEABLE BATTERY PACK,
USE ONLY THE APPROVED 5522-BATT RECHARGEABLE BATTERY PACK
FROM BAYCO PRODUCTS.
WARNING: TO PREVENT IGNITION OF A HAZARDOUS ATMOSPHERE, THE
RECHARGEABLE BATTERY PACK MUST ONLY BE EXCHANGED IN AN
AREA KNOWN TO BE NON-HAZARDOUS.
y Loosen the locking screw located on the side of the lens cap. CAUTION: Do
NOT attempt to completely remove the locking screw. Doing so is not necessary
and may damage the threads. The screw simply needs to be loosened enough
to allow the lens bezel to unscrew.
y Unscrew the lens bezel from the housing in a counter-clockwise direction.
y Loosen each of the two Charger Contact Pins located below the Floodlight Lens.
These two Screws should be loosened until approximately 1/8" of thread is visible.
CAUTION: Do NOT attempt to completely remove either of these two screws.
Doing so is not necessary and will potentially damage the light's ability to charge.
The two screws simply need to be loosened enough (approximately 1/8") to allow
the reflector / circuit assembly to be removed.
y Turn the light upside down and carefully shake the light in order to remove the
reflector / circuit assembly. Allow the reflector / circuit assembly to slide into your
hand. CAUTION: Do NOT touch the reflector surface with your finger. Doing so
may damage the reflector surface.
y Next, allow the 5522-BATT rechargeable battery pack to slide out of the light
paying close attention to the battery pack's orientation within the handle.
y Using only the approved replacement 5522-BATT rechargeable battery pack
from Bayco Products, slide the new battery pack into the handle of the light using
the directional arrow marked on the side of the pack to be a guide to proper
battery orientation.
y Align the reflector / circuit assembly so that the switches on the assembly are
aligned with the switches on the housing. Carefully insert the assembly back
into the flashlight housing until it is fully seated in the housing. CAUTION: Be
careful to not touch the reflector surface with your finger. Doing so may damage
the reflector surface.
y Tighten both of the Charger Contact Screws until they are fully seated.
CAUTION: Do NOT overtighten these two screws. Doing so may damage the
threads and impair the light's ability to properly charge.
y Replace the lens bezel by screwing it onto the housing in a clockwise direction.
y Tighten locking screw. CAUTION: Do NOT over-tighten. Doing so may
damage the threads and impact the light's Intrinsic Safety.
OPERATION
THE XPR-5522GM HAS FOUR SEPARATE LIGHTING MODES:
Momentary Flashlight Mode
Lightly press the top body switch for momentary operation. Release the switch
to turn the light off.
Constant-on Flashlight Mode
Press the top body switch until it clicks and then release for constant-on mode.
Press and release the top body switch again to turn the light off.
Floodlight Mode
Press the bottom body switch until it clicks and then release for floodlight
mode. Press and release the bottom body switch again to turn the light off.
Dual-Light Mode
Dual-Light allows the user to turn on both the Flashlight and the Floodlight, at the
same time. Press the top body switch until it clicks and then release for constant-
on mode Flashlight Mode. Next press and release the bottom switch to activate
the Floodlight. Both the Flashlight and the Floodlight are now running. Press and
release both the top and bottom body switches to turn the lights off.
WARRANTY
LIMITED LIFETIME WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship
and materials for the original purchaser's lifetime. The Limited Lifetime Warranty
includes the LEDs, housing and lenses. Rechargeable batteries, chargers, switches,
electronics and included accessories are warranted for a period of two years with
proof of purchase. Normal wear and failures which are caused by accidents, misuse,
abuse, faulty installation and lightning damage are excluded.
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
We will repair or replace this product should we determine it to be defective.
This is the only warranty, expressed or implied, including any warranty of
merchantability or fitness for a particular purpose.
For a complete copy of the warranty, go to www.nightstick.com/nightstick-
product-support/warranties. Retain your receipt for proof of purchase.
Mode d'emploi
Veuillez lire le mode d'emploi avant d'utiliser votre lampe Nightstick XPR-
5522GM. Il inclut des renseignements importants concernant la sécurité et le bon
fonctionnement de votre lampe de poche.
LA LAMPE XPR-5522GM EST APPROUVÉE POUR UTILISATION
Model XPR-5522GM Safety Flashlight
TESTED FOR INTRINSIC SAFETY IN METHANE-AIR MIXTURES ONLY
WARNINGS:
1)
MSHA approved for use with one part number 5522-BATT rechargeable
battery pack only.
2)
The Model XPR-5522GM Safety Flashlight is only to be charged on the
surface, or underground in accordance with the applicable regulations
pertaining to battery-charging stations (reference 30 CFR 75.340) with a
Bayco Products, Inc. model 5522-CHGR1.
3)
Do not open in areas where permissibility is required.
CLASS I DIV 1 GRPS A-D T3
CLASS II DIV 1 GRPS E-G T3 & Class III T165°C
CLASS I ZONE 0 AEx ia IIC T3 Ga
ZONE 20 GROUP IIIC T165°C
ID 4008947
Ex ia IIC T3 Ga
INTRINSICALLY SAFE
SECURITE INTRINSEQUE
0359
Conforms to:
ANSI/UL STD 913, ANSI/UL 60079-0,
ANSI/UL 60079-11
PART #: 5522-BATT
MANUFACTURER: BAYCO PRODUCTS
FOR USE ONLY WITH XPR-5522GM
CAUTION USE ONLY NIGHTSTICK CHARGERS RECHARGEABLE LITHIUM-ION 3.7v 2600mAh, 9.6w
DO NOT DISPOSE IN FIRE OR SHORT CIRCUIT
LIMITE DE CAPACITANCE - SÉCURITÉ INTRINSÈQUE
La capacité mesurée sur les deux aimants et la pince sur le côté excède 3pF
pour le Groupe IIC. Voici les valeurs de mesure pour la capacité. L'utilisateur
doit s'assurer de la conformité de l'équipement dans l'application finale.
Partie métallique
Aimant à la base du boîtier
Aimant sur le côté du boîtier
Pince sur le côté du boîtier
AVERTISSEMENTS – SÉCURITÉ INTRINSÈQUE
y Avertissement : Pour éviter l'inflammation d'atmosphère dangereuse, ne pas
placer le chargeur pour ce produit dans une zone dangereuse. Le chargeur pour
ce produit doit être placé UNIQUEMENT dans une zone non dangereuse.
y Avertissement : Pour éviter l'inflammation d'atmosphère dangereuse, ne pas
essayer de recharger ce produit dans une zone dangereuse. Cette tâche doit
être effectuée UNIQUEMENT dans une zone non dangereuse.
y Avertissement : Les batteries au lithium-ion doivent être utilisées et chargées
correctement. Une mauvaise utilisation peut causer des blessures graves, un
incendie ou la mort.
y Avertissement : Veuillez utiliser uniquement le bloc-piles rechargeable 5522-
BATT approuvé et inclut de Bayco Products.
INS-XPR-5522GM-16
XPR-5522GM
Bayco Products, Inc.
Permissible Flashlight Assembly
APPROVAL No. 20-A160002-0
II 1 G Ex ia op is IIC T3 Ga
Certified to:
CAN/CSA STD C22.2 No 157
CAN/CSA STD C22.2 No 60079-0
CAN/CSA STD C22.2 No 60079-11
CSA STD C22.2 No 25
Capacité mesurée en pF
4.03
3.1
4.3
Ex ia op is IIC T3 Ga
Intertek ITS 16 ATEX201022X
IECEx ITS 16.0045X
-10ºC ≤ Tamb ≤ +40ºC IP54
3.7V/Cell
Input entity parameters for
charging contacts on flashlight:
U
4.75V
i
I
500mA L
0.0uH
i
i
P
0.59W C
0.0uF
i
i
07-23-2018
Publicité
Table des Matières
