DeWalt DWE314 Traduction De La Notice D'instructions Originale page 24

EngLIsh
5) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional Safety Rules for Oscillating Multi-
Tool

WARNING: Take special care when sanding some woods
(e.g. beech, oak) and metal which may produce toxic dust.
Wear a dust mask specifically designed for protection
against toxic dust and fumes and ensure that persons
within or entering the work area are also protected.

WARNING: Use this tool in a well-ventilated area when
sanding ferrous metals. Do not operate the tool near
flammable liquids, gases or dust. Sparks or hot particles
from sanding or arcing motor brushes may ignite
combustible materials.
Sanding Paint

WARNING: Observe the applicable regulations for
sanding paint. Pay special attention to the following:
• Whenever possible, use a vacuum extractor for dust collection.
• Take special care when sanding paint which is possibly lead
based:
Do not let children or pregnant women enter the
-
work area.
- All persons entering the work area should wear a mask
specially designed for protection against lead paint dust
and fumes.
- Do not eat, drink or smoke in the work area.
• Dispose of dust particles and any other removal debris safely.
Hold power tool by insulated gripping surfaces when
•
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a "live"
wire will make exposed metal parts of the tool "live" and shock
the operator.
• Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and may
lead to loss of control.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot
during operation.
• Risk of personal injury due to prolonged use.
22
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your D WALT tool is double insulated in accordance
e
with EN60745; therefore no earth wire is required.

WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1.5 mm
is 30 m.
When using a cable reel, always unwind the cable completely.
Package Contents
The package contains:
1 Adaptor for all blades (DWE315SF, DWE315B, DWE315KT,
DWE314K)
1 Dust extraction adaptor (DWE315KT)
1 Cutting guide (DWE315KT)
1 31 mm x 43 mm fastcut wood blade (DWE314K, DWE315KT)
1 31 mm x 43 mm wood with nails blade (DWE315SF,
DWE315KT, DWE315B, DWE314K)
1 100 mm Semicircle blade (DWE314K, DWE315KT)
1 Sanding-pad (DWE314K, DW315, DWE315B, DWE315KT)
25 Assorted sandpaper pieces (DWE314K, DW315, DWE315B,
DWE315KT)
1 9.5 mm x 43 mm wood detail blade (DWE315KT)
1 3 mm Carbide grout removal blade
(100 mm half moon) (DWE315KT)
1 Rigid scraper blade (DWE315SF, DWE315B, DWE315KT,
DWE314K)
1 Hex key (DWE315SF, DWE315B, DWE315KT, DWE314K)
1 Kit box (DWE314K, DWE315KT)
1 Kit bag (DWE315B)
WALT
e
; the maximum length
2