Sleep Timer; Alarm Clock; System Settings - Loewe klang s1 Guide De L'utilisateur

Loewe klang s1/s3

Bluetooth Audio | CD (klang s3 only) | Sleep timer | Alarm clock

System Settings

14.1 Pairing Bluetooth devices
for the first time
Make sure that the terminal device to be pai-
red is switched on and Bluetooth is activated.
Select the source [Bluetooth Audio] in the
home menu. The [Bluetooth Discoverable]
appears on the display. Now open the Bluetooth
settings on the terminal device to be paired and
start searching for available Bluetooth devices
there. Select "Loewe klang s1 (s3)" and start the
pairing process.
After successful pairing, [Connected] appears
on the display. Now the music playback can be
controlled via the phone/tablet. To do this, use
the music App of your choice.
Basic operation of play/pause and skip forward/
backward is possible using the corresponding
buttons on the remote control.
Note: Some devices require a PIN code when
connecting, then enter "0000".
14.2 Automatic connection after
pairing has already taken
place
If the source is switched from [Bluetooth
Audio] or the radio is switched off, the Blue-
tooth connection is disconnected. If the radio
is switched on again or switched back to the
[Bluetooth Audio] source, an automatic con-
nection is established.
Note: If an automatic connection is not possible,
please proceed as follows:
button and select [View details].
Press the
Then open the [Paired Device List], to select
and connect the desired device. Press the OK
button to establish the connection and [Con-
nected] appears briefly on the display.
14.3 Pairing another device
To connect another device to the radio, plea-
se press the button and select [Setup
Bluetooth]. This will disconnect the current
connection.
Now proceed as when you first pair a device.
Afterwards, this device is also saved in the list
of paired devices and can be selected via the
corresponding menu (see above). A maximum
of 8 devices can be saved.
15 CD (klang s3 only)
You can use this source to listen to your CDs.
Please select the source [CD] in the home menu.
15.1 CD playback
Insert a disc into the CD compartment. Only
standard 12 cm discs are supported. Make sure
the CD label side is facing the front side of the
radio. The CD starts playing automatically. Press
or repeatedly to skip to the previous/next
track. Press and hold or
forward current track.
24
Tip: Insert a CD when the radio is in standby
mode. The radio wakes up and starts playing
the disc.
Note: Some MP3 files may not be supported.
15.2 Random play and repeat
To play CD tracks/MP3 files in random order or
play files repeatedly:
To turn on shuffle play, press the
select [Shuffle] and press OK to confirm. Then
select option [On] and press the OK button
again to confirm.
To repeat tracks, press the
[Repeat] and press OK to confirm. Then select
[Repeat 1] to repeat one track or [Repeat all]
to repeat all tracks. Confirm your selection by
pressing the OK button.
15.3 Ejecting a CD
To eject the disc from the CD compartment,
press the
16

Sleep timer

With this function you can switch the radio
to standby mode automatically after a set
period of time. You can choose between 15,
30, 45 or 60 minutes, [Sleep OFF] deletes
the previously set period of time. To do this,
press the
selected and select [Main menu]. Use the
or to navigate in the menu and select
[Sleep]. Use the
sleep time] menu to select the desired
time period and confirm with the OK button.
Exit the menus again with the
Alternatively, you can use the
remote control to set the time period.
The remaining time is shown in the bottom left
of the display, with minutes running backwards.
17

Alarm clock

This radio has 2 individually adjustable alarm
times. You can call up the alarm clock from the
main menu. Press the
source is selected and select [Alarms].
17.1 Enable
Select here on which days the alarm should be
activated. The following selection is available:
[Off] / [Daily] / [Once] / [Weekend] /
[Weekdays]
Select [Off] to deactivate an activated alarm
clock.
17.2 Time
Set the hours first with the
then the minutes after pressing the OK.
to rewind or fast
button,
button, select
button on the radio.
button while the audio source is
or button in the [Set
button.
button on the
button while the audio
or buttons and
17.3 Mode
Here you set the audio source with which you
want to wake up. The following selection is
available: [Buzzer] / [Internet radio] / [DAB]
/ [FM]
17.4 Preset
The station with which to wake up is specified
here. The station last listened to or the stations
saved in the favourites are available here. Does
not apply to buzzer mode.
17.5 Volume
Set the desired alarm volume here.
17.6 Save
Once you have made all the settings, please
press the OK button to save the settings.
An activated alarm clock is shown with an alarm
symbol and the number of the active alarm clock
at the bottom left of the display. In standby mode
you can also see the set alarm time.
17.7 Switching off the alarm
clock after waking up
To switch off the alarm clock until the next alarm
cycle, please press the button on the device
or on the remote control [Alarm off] appears
briefly on the display. If you only want to interrupt
the alarm function for a few minutes (snooze),
you can use any other button. The alarm delay
is set by pressing a button in steps 5, 10, 15 and
30 minutes and can also be extended again and
again. After a short time, the radio automatically
switches back to [Standby] and the time re-
maining until waking up again is displayed next
to the flashing alarm symbol.
Note: The saved wake-up times are retained in
the event of a power failure.
18 System settings
In the system settings you can change the
settings of the radio and call up important infor-
mation about it. To display the System settings
menu, press the button on the remote control
or press and hold the button on the radio. The
menu of selected audio mode is displayed. In
this menu, select [System settings] to open
the System settings menu. The [System set-
tings] menu contains following choices:
ƒ [Equaliser]
ƒ [Network]
ƒ [Time/Date]
ƒ [Language]
ƒ [Factory reset]
ƒ [Software update]
ƒ [Setup wizard]