Publicité
Les langues disponibles
Les langues disponibles
OPERATING INSTRUCTIONS
PLUG-IN POWER ADAPTER
ITEM NO.: 51 83 74 SNG-600-OW
ITEM NO.: 51 55 11 SNG-1000-OW
ITEM NO.: 51 55 12 SNG-1500-OW
ITEM NO.: 51 55 13 SNG-2250-OW
INTENDED USE
This product is designed to supply electric devices with power. It is particularly suited for
operating decorative LED or LED strip lighting installations such as nativity set lighting or
modern direct or indirect lighting of display cabinets, picture frames or mirrors. The connected
load's current consumption must not exceed the maximum output rating of the product. Power
is supplied via a standard mains socket (100 – 240 V/AC, 50/60 Hz). Various voltages can be
set with the key. The product should only be used in dry indoor areas. The product features
both short-circuit and overload protection.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If
you use the product for purposes other than those described above, the product may be dam-
aged. In addition, improper use can cause hazards such as short circuiting, fire, electric shock
etc. Read the instructions carefully and keep them. Make this product available to third parties
only together with its operating instructions.
DELIVERY CONTENT
• Power adapter
• Key
• Operating instructions
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product..
• The product should not be used immediately after it has been brought from an
area of cold temperature to an area of warm temperature. Condensed water might
destroy the product. Wait until the product adapts to the new ambient temperature
before use.
• Make sure that the output of the power adapter is not short-circuited.
• Never pour liquids over electrical appliances and never leave objects filled with
liquids (e.g. vases) on it or in the vicinity. There is a high risk of fire or life-threatening
electric shock.
• Always lay the cables so that nobody can trip over or become entangled in them.
This poses a risk of injury.
• When setting up the product, make sure that the cable is not pinched, kinked or
damaged by sharp edges.
• The plug must be pulled out of the socket under the following conditions:
- before cleaning the product
- during a thunder storm
- if the product is not being used over a long period.
b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the
device.
VERSION 10/12
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
If you are not sure about the correct connection or use, or if questions arise which are not
covered by these operating instructions, please do not hesitate to contact our technical support
or another qualified specialist.
Voltcraft®, Lindenweg 15, D-92242 Hirschau, Tel. +49 180/586 582 7.
OPERATION
Ensure the polarity is correct when establishing a connection. The positive
terminal of the cable is identified by a white line and a sticker showing a +.
Ensure the power supply unit's open ends are insulated with suitable insulating
material at all times. This applies to the power supply unit whether it is installed
or not.
Always unplug the power plug first before disconnecting the connectors from
the consumer.
1. LEDs and LED strips already feature soldering points where the power supply unit's open
ends can be attached. Ensure the polarity is correct. After assembly, insulate the connections
with suitable insulating material such as heat shrink tubing.
2. Set the required voltage (3 / 4.5 / 5 / 6 / 7.5 / 9 / 12 V/DC) with the key.
3. Connect the mains plug to a standard mains socket (100 – 240 V/AC, 50/60 Hz). The LED
on the top of the power adapter indicates operational readiness.
4. Remove the power adapter from the mains when it is no longer in use.
CLEANING
• When cleaning, the power adapter must be disconnected from mains socket.
• Only use dry and soft cloth to clear the housing of the power adapter.
• Do not use abrasive or solvents.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the household
waste!
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
TECHNICAL DATA
Item No.:
Input voltage:
Output voltage:
Output current:
Cable length:
Operating temperature:
Operating humidity:
Storage temperature:
Storage humidity:
Dimensions
(W x H x D):
Weight:
Legal notice
These operating instructions are a publication by Voltcraft®, Lindenweg 15, D-92242 Hirschau/Germany, Phone +49 180/586 582 7
(www.voltcraft.de).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2012 by Voltcraft®
51 83 74
51 55 11
51 55 12
100 – 240 V/AC, 50/60 Hz
3 / 4.5 / 5 / 6 / 7.5 / 9 / 12 V/DC
0,6 A max.
1 A max.
1,5 A max.
1.8 m
0 to +35 °C
20 – 85 %
-20 to +50 °C
10 – 90 %
68 x 39 x 68
76 x 42.4 x 72
82 x 51 x 73.2
mm
mm
95 g
110 g
145 g
51 55 13
2,25 A max.
87.5 x 51 x 77.3
mm
mm
200 g
Publicité
