Important Safety Instructions - Newa Pond PURO advance PR adv 1 Mode D'emploi

IMPORTANT SAFETY INSTRUCTIONS

PURO/PURISSIMO adv is a complete filtering system
for freshwater ornamental outdoor ponds. Any other
use is prohibited and, consequently, not covered by the
manufacturer's liability.
WARNING: this appliance cannot
be used by children under eight
or persons with reduced physical,
sensory or mental capabilities, or lack
of experience and knowledge, unless
they have been given supervision
or instructions concerning use of
the appliance in a safe way and
understand the risks involved.
WARNING: Children shall not play
with the appliance because this is
not a toy. Cleaning and maintenance
shall not be made by children without
supervision.
SAVE THESE INSTRUCTIONS CAREFULLY!
INSTALLATION
PURO adv: Follow the instructions on pages 12-13-14-15.
PURISSIMO adv: Follow the instructions on pages 16-17-18-19.
(Refer to the components listed on page 24).
WARNING - PRS adv: It is recommended to place
the filter close to the edge of the pond, making sure
to place it on a level surface and on an area that is
not subject to flooding or overflow or where it might
accidentally end up in the water and that the distance
between the filter installation point and the pond edge
is minimum 2 m. The components and the tightening
spanner (5) are inside the accessory bag found inside
the filter. WARNING: to fit the water outlet opening it
is necessary to take out the basket containing the bio-
balls. Then insert the outlet opening (14) fastening it
with the relative sealing ring and nut (fig 7 and 11).
PURO adv: Install the sealing ring (6) on the hose
connector (13) and screw it to the valve (20). Fasten
the latter to the filter inlet using the proper sealing ring
(6) and lock it joining the sleeve(19) to the deflector
(18). In order to operate, the PURO filters must be
connected to a pump not supplied (fig.1-2 on page
12). The valve provided with the filter must be used to
adjust water flow in the filter inlet. For best performance
it is recommended to adjust the flow until you reach
the level indicated on the "WATER LEVEL" label (fig.5).
English
PURISSIMO adv: Install the support hook (12) of
the UV-C filter on the edge of the basin. Holding the UVC
filter in a slightly tilted position to pass over the previously
positioned support hook, assemble the UV-C by inserting
the respective gasket (6) on the screwed joint of the UVC
filter and the latter directly on the specific opening on the
side of the body of the PURISSIMO adv. filter
Set the body of the UVC filter on the hook and fasten
everything with the sleeve (19) and the deflector (18).
PRS adv 1: screw the hose connector complete with nut
and sealing ring to the UV-C filter's inlet.
PRS adv 2/3: screw the hose connector complete with nut
and sealing ring to the valve . Fasten the latter to the UV-C
filter's inlet (fig.7) using the proper sealing ring (6).
Connect the pump to the UV-C filter's inlet through the
spiral tube provided in the box. The UV-C filter must
not be immersed in water. For more information on
the installation of the pump and UV-C filter consult the
relative instruction booklets . The valve must be used to
adjust water flow in the filter's inlet in case you are using
a pump with higher performances than the one supplied
in the box.
PRS adv 2/3: for best performance it is recommended
to adjust flow until you reach the level indicated on
the "WATER LEVEL" label (fig.5).
MAINTENANCE
In order to maintain optimal filtration it is recommended
to periodically inspect the clogging status of the filtering
media. Release the hooks and remove the covers. If the
water level of the first basin reaches the OVER FLOW
four holes (see page 14 and 15), it is recommended to
proceed with the filter maintenance . Disconnect the pump
and wait until the filter is completely empty. Remove the
baskets and wash the filtering materials with running
water. To take out the drum next to the water inlet it is
necessary to unscrew first the sleeve with the deflector.
Do not use chemical detergents. Before reassembling the
baskets, make sure to have completely removed the dirt
present on the basins bottom. Reassemble the baskets
in the filter paying attention that the numbers present on
the basin correspond to those indicated on the baskets.
These will be correctly placed only if the basket lame will be
inserted in the corresponding track of the basin up to the
coupling (fig.8). Close the covers paying attention to the
joining hooks (fig.9).
PUMP AND UV-C FILTER MAINTENANCE
For PURISSIMO models only: following the instructions
provided in the relevant instruction booklets for
maintenance.
TROUBLESHOOTING
If little water comes out of the filter:
• Check that the pump's suction is clean and obstacle-free.
3 / 28