Transport And Installation; Noise Emission; Content Of Delivery - Jet JMD-18PF Mode D'emploi

Mains 230V ~1L/N/PE 50Hz
Output power 0,75 kW (1 HP) S1
Reference current
Extension cord (H07RN-F):
Installation fuse protection
JMD-18:
Drilling capacity
Milling capacity of face mill
Milling capacity of end mill
Spindle to column
Distance table to spindle max 455mm
Spindle taper
Draw bar
Spindle travel
Column diameter
Spindle speeds...12
Max travel X-axis
Max travel Y-axis
Table size
T-slots...4
Overall (LxWxH) 1080x1010x1105mm
Net weight
Mains 230V ~1L/N/PE 50Hz
Output power 1,5 kW (2 HP) S1
Reference current
Extension cord (H07RN-F):
Installation fuse protection
JMD-18PF:
Power feed mechanism
0,12 / 0,18/ 0,25 mm/rev
Spindle travel in auto feed
Net weight

4.2 Noise emission

Acoustic pressure level (EN 11202):
Idling at maximum speed 76,5 dB (A)
The specified values are emission levels
and are not necessarily to be seen as
safe operating levels.
As workplace conditions vary, this
information is intended to allow the user
to make a better estimation of the
hazards and risks involved only.

4.3 Content of delivery

Machine light
Tiltable vice
13mm drill chuck with arbour MT3
Face mill dia 63mm (JMD-15)
Face mill dia 75mm (JMD-18, -18PF)
Draw bar M12
3 Downfeed handles
Head rising crank and handle
3 Table handwheels
Lifting Hook
Operating tools
Operating manual
Spare parts list.
5. Transport and start up

5.1 Transport and installation

7.6 A
3x1,5²
The machine will be delivered in a
10A
closed crate.
For transport use a forklift or hand
30mm
trolley. Make sure the machine does
75mm
not tip or fall off during transport.
20mm
The machine is designed to operate in
200mm
closed rooms and must be bolted to the
cabinet stand or a solid work bench.
MT-3
M12
For packing reasons the machine is not
125mm
completely assembled.
115mm
125-2500rpm
520mm
5.2 Assembly
175mm
240 x 805mm
If you notice transport damage while
16mm
unpacking, notify your supplier
immediately. Do not operate the
machine!
276 kg
Dispose of the packing in an
environmentally friendly manner.
Clean all rust protected surfaces with
12 A
petroleum, diesel oil or a mild solvent.
3x1,5²
Screw rubber handles (A, Fig 1) onto
16A
handle rods (B). Screw handle rod into
downfeed hub (C) and tighten.
107mm
276 kg
Slide crank (D, Fig 2) onto shaft and
tighten set screw (E).
Install handle (F).
Slide handwheels (G, Fig 3) onto table
handwheel shafts and tighten set
screws.
Install handle (H)
Fig 1
Fig 2
5
Fig 3
Mounting machine to stand or solid
workbench.
Unbolt the lathe from the shipping crate
bottom.
Open the pulley cover and use the
lifting hook to lift the machine (see Fig
4)
Fig 4
Caution:
The machine is heavy.
JMD-15 = 185 kg!
JMD-18 = 276 kg!
JMD-18PF = 276 kg!
Assure the sufficient load capacity
and proper condition of your lifting
devices.
Never step underneath suspended
loads.
Carefully place the machine onto the
cabinet stand or a solid work bench.
Bolt together machine and cabinet
stand or workbench (Fig 5).