Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
a) Checking the battery level
• To check the level of the internal battery, briefly press the battery function button (7). The
battery level will be displayed as follows by the LED battery level indicator (9).
5
At very low charge levels (< 4 %), the battery level check may not work or charging
may not work. Instead, the LED on the product lights up briefly.
b) Charging the battery
• Charge the power bank's internal battery when a battery level of below 25 % is indicated.
• Open the cap and connect the micro USB cable to the USB micro port (2).
• Connect the USB-A connector on the micro USB cable to a USB port on a computer or another
suitable USB power source, such as a USB power adapter. Charging will start automatically
when the USB power source delivers a current. The LED battery level indicator (9) blinks to
indicate that the battery is charging.
• Remove the product from the USB power source when the LED indicates that the battery is
fully charged.
• All four LEDs in the LED battery level indicator (9) are illuminated when the battery is fully
charged. The device is now fully charged and ready for use.
c) Using the light
• Remove the cap covering the thumbwheel (1) as shown in the diagram.
• Turn the thumbwheel (1) clockwise. A click confirms that it has been switched on. Turn the
thumbwheel (1) anti-clockwise. A click confirms that it has been switched off. Turning the
thumbwheel (1) clockwise increases the brightness of the light and turning it anti-clockwise
reduces the brightness.
※
d) Other light functions
Setting the colour temperature
10
Press the light function button (10) until the
desired light colour is set.
Warm > Bright > Daylight are available.
e) Power bank functions
• Connect the mobile device to be charged to the USB-A port (4) using the USB cable supplied,
as shown in the diagram.
• Press the battery function button (7) to start charging your mobile device. The LED battery
level indicator (9) indicates the battery level of the internal batteries briefly and then turns off
again. The charging function is switched off after approximately 90 seconds when not in use
(e.g. the charger cable is not connected) and must be started again.
0 - 25 % capacity remaining
25 - 50 % capacity remaining
50 - 75 % capacity remaining
75 - 100 % capacity remaining
2
1
1
SOS function
10
Press and hold the light function button (10)
for approximately 2 seconds to switch on
the SOS function. Pressing this button again
switches it off again; or you can switch the
light off completely using the thumbwheel.
4
f) Setting up and positioning
You can set up the light using the adjustable handle and direct the beam as desired.
• Click the supplied S-hooks into the appropriate place on the handles.
• Hang the light in a suitable place. Point the light in the desired direction.
g) Storage and transport
• Close the two caps and store the product in the tightly closed storage pouch when not using
or when transporting the device.
Care and cleaning
• Always disconnect the product from the power supply before cleaning it.
• Disconnect the USB cable and connected mobile devices from the product before cleaning.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the casing or cause the product to malfunction.
• Use a damp, lint-free cloth to clean the product. Do not press too hard on the housing, as this
can lead to scratch marks.
• Do not immerse the product in water.
• Clean all sealing surfaces of the caps.
• The product does not contain any components that require maintenance. Never attempt to
open or disassemble it.
Disposal
Electronic devices are recyclable waste and must not be placed in household waste.
Always dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Input voltage/current ..................... 5 V/DC, 2 A
Output voltage/current .................. 5 V/DC, 1.5 A
Power consumption (LED) ............ 3.75 Wh
Power consumption (total) ............ 4.5 Wh
Internal rechargeable battery ........ Li-Ion, 10400 mAh, 37.44 Wh
Charging time ............................... Approx. 7 hours
Operating time .............................. Max. 8 - 80 hours, 6 to 50 (for winter operation)
LED ............................................... 64
Colour temperature ....................... 3000 K / 4290 K / 6200 K (variable)
Luminous flux ............................... 30 lm to 1000 lm
Cable length ................................. 20 cm
Protection rating ........................... IP44
Operating conditions ..................... -10 to +40 °C, 10 – 80 % relative humidity (non-
Storage conditions ........................ -10 to +60 °C, 5 – 85 % relative humidity (non-condensing)
7
Dimensions (L x W x H) ................ 160 x 90 x 34 mm
Weight .......................................... 390 g
These operating instructions are published by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower 2,
Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved.
Reproduction by any method (e.g. photocopying, microfilming, or the capture in electronic data processing systems)
requires prior written approval from the editor. Reprinting, also in part, is prohibited. These operating instructions reflect the
current technical specifications at the time of printing.
Copyright 2017 by CEI Conrad Electronic International (HK) Limited
condensing)
*1552831_v1_1017_02_DS_m_4L_(1)
Publicité
Table des Matières
