Technical Data; Cleaning And Maintenance - MSW S-SAW350 Manuel D'utilisation

19. Do not touch movable parts or accessories unless
the power source has been disconnected.
20. Use your tool at lower input load than specified on
the nameplate to increase working efficiency and
decrease wear out.
21. Do not wipe plastic parts with solvent. Solvents such
as gasoline, thinner, benzene, alcohol, ammonia and
oil may damage and crack plastic parts. Do not wipe
them with such solvents. Wipe plastic parts with
a soft cloth lightly dampened with soapy water.
22. Wear protective goggles to protect your eyes.
23. Use dust masks.
24. Use earplugs to keep your ears noise-free while
working.
25. The tool becomes very hot during operation.
26. Dress properly. Do not wear loose clothing
or jewellery. They can get caught in moving
parts. Rubber gloves and non-skid footwear are
recommended when working outdoors. Wear
protective hair covering to contain long hair.
27. When transporting and handling the stone saw
between the warehouse and the destination, take
into account the occupational health and safety
principles for manual transport operations which
apply in the country where the stone saw will be
used.
Failure to follow safety recommendations
instructions may result in serious injuries or death!

TECHNICAL DATA

Product name Stone Saw
Model S- S- S-
SAW350 SAW400 SAW450
Rated voltage [V] 230~
Frequency [Hz] 50
Rated power [W] 2000
Rated operation cycle S6 – 40%
Saw blade diameter 350 400 450
[mm]
Worktable 530 x 430
dimensions [mm]
Safety class IP IP54 IP54 IP54
Saw blade speed 2800 3000 2800
without loading [rpm]
Maximum cutting 800 700 700
length [mm]
Maximum cutting 100 120 140
depth [mm]
Maximum workpiece At 90° – 90
thickness [mm] At 45° – 65
Maximum workpiece 0 – 45
thickness [°]
Sound power level L 90dB(A),
wA
Uncertainty k-3dB(A)
Sound pressure 77dB(A),
level L Uncertainty k=3dB(A)
pA
8
Weight [kg] 90 77
SCOPE OF APPLICATION
The stone saw is designed for wet cutting stone, bricks,
tiles, construction materials, etc. with the use of water as
the cooling agent.
The user is liable for any damage resulting from non-
intended use of the device.
ATTENTION! Do not use the machine to cut wood or metal.
BEFORE THE FIRST USE
Upon receipt of the goods, check the packaging for
integrity and open it. If the packaging is damaged, please
contact your transport company and distributor within 3
days, and document the damages as detailed as possible.
Do not turn the package upside down! When transporting
the package, please ensure that it is kept horizontal and
stable.
DISPOSAL OF THE PACKAGING
Please keep all packaging materials (cardboard, plastic
tapes and Styrofoam), so that in case of a problem, the
device can be sent back to the service centre in accurate
condition!
INSTALLING THE APPLIANCE
and
APPLIANCE LOCATION
Place the device on a stable surface, where the is no
risk of sliding. Ensure sufficient space for safe device
operation. Use the device in well illuminated spaces. Ensure
unobstructed access to the electricity plug at all times.
Make sure the power source reflects the parameters on the
rating plate!
PRINCIPLE OF OPERATION
Front view
7 8
9
6
4
5
2
3
1
1
Rear view
10
11
11
12
13
14
15
Rev. 10.10.2017
1. retractable feet
90
2. guide
3. water tank
4. conveyor
5. cutting angle guide
6. saw blade
7. Cutting height adjustment handle
8. Cutting angle adjustment handle
9. ON(I) / OFF(0) button
10. water valve
11. cutting height lock
12. cutting angle adjustment tool
13. spatter guard
14. carry handle
15. transport wheels
Before switching the device on: make sure the water tank
outflow is plugged, fill tank with water, no more than
one centimetre from the top of the tank (the pump inlet
has to be submerged). Then place the workpiece on the
conveyor, set the required cutting angle and height. Turn
on the device and open the water valve. Start cutting once
water starts flowing over the saw blade. Move the conveyor
gently so as to prevent the saw blade from snagging.
ASSEMBLY / DISASSEMBLY OF THE DEVICE'S ELEMENTS
1. Unfolding the legs:
Lift one side of the machine, fold out the spring mounted
legs and ensure the bolt sits in the notch:
Then do the same with the legs on the other side.
2. Assembling transport wheels:
The machine is equipped with 2 wheels for transporting it
over short distances. Slide 2 washers over the bolt, inset
a wheel into the bracket and then thread the bolt through
the bracket and wheel. Then slide 2 more washers onto the
bolt and a nut. Use two spanners to tighten. Assemble the
other wheel in analogous manner.
3. Conveyor assembly:
Mount the conveyor onto the guide. Make sure the
conveyor wheels are on the guide and the lower conveyor
arrestor should be under the right-hand side guide.
4. Replacing the saw blade:
Remove 4 nuts from the saw blade guard. remove the
guard. Make sure you do not damage the hose feeding the
cooling water to the saw blade.
Insert spanner over the saw blade bolt and then slide pin
through the hole to prevent saw blade from spinning.
Rev. 10.10.2017
Remove the old saw blade and mount new blade. make
sure the arrows on the blade point in the correct direction.
Insert nut, lock the blade and tighten it. Then mount the
guard and tighten the 4 nuts.
TRANSPORTATION AND STORAGE
During transport, the machine should be protected from
shaking, falling and turning upside down. Store it in
a properly ventilated place with dry air and without any
corrosive gas. The device should be stored with the water
system (hoses and valve cutting off water supply to the
hoses) emptied and cleaned. The water tank should be
emptied. Remove all contaminants and waste from it.
REVIEWS
Before using the machine, the new or repaired machine
must be checked by qualified technical personnel who have
knowledge and experience within the scope of operation
and maintenance of this type of machine. The machine
must be checked regularly by means of visual control of
the machine's condition, before, during and after use. The
check must be performed by the machine's operators. Any
irregularities in machine operation, as well as any damage
must be reported to the proper technical personnel. Do
not use the machine if damage or any irregularities in its
operation were found.

CLEANING AND MAINTENANCE

• Always unplug the device before cleaning it and after
each use.
• Use cleaner without corrosive substances to clean
surface.
• At the end of each work day, clean the tank and any
deposits. If the machine is used continuously, this
should be performed three times a day.
• Clean the water pump sieve every day.
• Use a damp cloth to clean the surface of the device.
Use a soft brush for more stubborn stains.
• Store the unit in a dry, cool location, free from
moisture and direct exposure to sunlight.
ATTENTION! Unplug the power cable from the socket and
secure the saw blade before carrying out any maintenance!
CHECK REGULARLY THE DEVICE
Check regularly the machine for signs of damage. If the
machine is damaged, please stop using it immediately and
contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare following
information:
• Invoice number and serial number (the latter is to be
found on the technical plate on the machine).
• If relevant, take a picture of the damaged, broken or
defective part.
• It will be easier for your customer service clerk to
determine the source of the problem if you give
a detailed and precise description of the matter. The
more detailed your information, the better customer
service will be able to solve your problem rapidly and
efficiently!
CAUTION: Never open the machine without
authorization of your customer service. This can lead to
a loss of warranty!
the
9