Operation (For Wired Remote Controller); Operation Mode - Mitsubishi Electric CITY MULTI PLFY-EP NEMU-E Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

3. Operation (For Wired Remote controller)

About the operation method, refer to the operation manual that comes with each remote controller.
3.1. Turning ON/OFF
[ON]
ON
OFF
Note:
Even if you press the ON/OFF button immediately after shutting down the operation is progress, the air conditioner will not start for about 3 minutes.
This is to prevent the internal components from being damaged.
Operation status memory

Operation mode

Preset temperature
Fan speed
Settable preset temperature range
Operation mode
COOL/DRYING
HEAT
AUTO (single set point)
AUTO (dual set point)
SETBACK
FAN, VENTI.
*1 The preset temperatures for cooling and heating for AUTO (dual set point) mode will be used for those for COOL/DRYING and HEAT mode.
*2 The preset temperatures for cooling and heating can be set under the following conditions.
• The cooling preset temperature is greater than the heating preset temperature.
• The difference between the cooling and heating preset temperatures is equal or greater than the minimum temperature difference that varies depending on the indoor
unit model to be connected.
The settable temperature range varies with the model of outdoor units and remote controller.
3.2. Operation mode
Fri
83
Room
Cool
Set temp.
Auto
83
Mode
Temp.
Fan
ON
RETURN SELECT
MENU
OFF
HOLD
en
What the blinking mode icon means
The mode icon will blink when other indoor units in the same refrigerant
system (connected to the same outdoor unit) are already operated in a
different mode. In this case, the rest of the unit in the same group can
only be operated in the same mode.
5
Press the [ON/OFF] button.
The ON/OFF lamp will light up in green,
and the operation will start.
When "LED lighting" is set to "No", the
ON/OFF lamp will not light up.
Remote controller setting
Operation mode before the power was turned off
Preset temperature before the power was turned off
Fan speed before the power was turned off
Preset temperature range
67 - 87 (95) °F/19 - 30 (35) °C
63 (40) - 83 °F/17 (4.5) - 28 °C
67 - 83 °F/19 - 28 °C
[COOL] Preset temperature range for COOL mode.
[HEAT] Preset temperature range for HEAT mode. *1, *2
[COOL] Preset temperature range for COOL mode.
[HEAT] Preset temperature range for HEAT mode. *2
Unsettable
Each pressing of the [F1] button cycles
through the following operation modes.
Select the desired operation mode.
Cool
Drying
Auto
Heat
• Operation modes that are not available
to the connected outdoor unit models will
not appear on the display.
[OFF]
ON
OFF
3.3. Temperature setting
<Cool, Drying, Heat, and Auto (Single set point)>
Fri
83
Room
Cool
Set temp.
Auto
83
Fan
Mode
Temp.
Fan
Setback
RETURN SELECT
MENU
HOLD
Press the [F2] button to decrease the preset temperature, and press the
[F3] button to increase.
• Refer to the table on page 5 for the settable temperature range for dif-
ferent operation modes.
• Preset temperature range cannot be set for Fan/Ventilation operation.
• Preset temperature will be displayed either in Centigrade in 0.5- or
1-degree increments, or in Fahrenheit, depending on the indoor unit
model and the display mode setting on the remote controller.
Press the [ON/OFF] button again.
The ON/OFF lamp will come off, and
the operation will stop.
Operation mode
Room temperature (Refer to the Installation Manual.)
ON
OFF

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

City multi plfy-ep nemu-e1

Table des Matières