Accessories; Protecting The Environment; Technical Data - Stanley FATMAX FMEH850 Traduction Des Instructions Originales

ENGLISH
Set the depth gauge (not supplied) to the desired position.
u
The maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth gauge.
Tighten the side handle by turning the grip clockwise.
u
Fitting an accessory (fig. B)
Open the chuck by turning the sleeve (6) counterclock-
u
wise.
Insert the bit shaft (9) into the chuck.
u
Tighten the chuck by turning the sleeve clockwise.
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Switching on and off (fig. C, D)
Select the required speed by turning the speed selector
u
dial (5) as shown in figure C.
To switch the tool on, press the variable speed switch (1).
u
The tool speed depends on how far you press the switch.
For continuous operation, press the lock-on button (2) and
u
release the variable speed switch. This option does not
work in reverse rotation.
To switch the tool off, release the variable speed switch.
u
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
Selecting the direction of rotation (fig. E)
For drilling and tightening screws, use forward
(clockwise)
rotation. For loosening screws or removing a
jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse slider
u
(3) to the left.
To select reverse rotation, push the forward/reverse slider
u
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Selecting the drilling mode (fig. F)
For Impact drilling in masonry and concrete, set the
u
drilling mode selector (4) to the
For drilling in steel, wood and plastics or for screw driving
u
set the operating mode selector (4) to the

Accessories

The performance of your tool depends on the accessory used.
Stanley Fat Max accessories are engineered to high quality
standards and designed to enhance the performance of your
6
(Original instructions)
q
position.
r
position.
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.

Protecting the environment

Separate collection. Products and batteries marked with this
symbol must not be disposed of with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions.
Further information is available at www.2helpU.com

Technical data

Input voltage
V
AC
No-load speed min
-1
Impact rate min
-1
Weight kg
Max. drilling capacity
Concrete mm
Steel mm
Wood
mm
FMEH850 (Type 1) FMEH1100 (Type 1)
230
0~1100/0~3200 0~1100/0~3200
0~18700/0~54400 0~18700/0~54400
2.4
18
13
50
230
2.6
18
13
50