Specifications; Installation And Wire Connection; Before Starting; Installation Cautions - Clarion CMS4 Manuel Du Propriétaire Et Manuel D'installation

7. SPECIFICATIONS

FM Tuner
Frequency Range: USA 87.9 - 107.9MHz
Europe 87.5 - 108.0MHz
Asia 87.5 - 108.0MHz
Australia 87.5 - 108.0MHz
Usable Sensitivity: 4 µV (S/N=30dB)
Image Rejection: >45dB
Stereo Separation: >25dB
AM Tuner
Frequency Range: USA 530 -1710KHz
Europe 531 - 1602KHz
Asia 531 - 1629KHz
Australia 531- 1629KHz
Usable Sensitivity: 40dB (S/N=20dB)
Weather Band Selection
CH.1 162.400MHz CH.2 162.425MHz
CH.3 162.450MHz CH.4 162.475MHz
CH.5 162.500MHz CH.6 162.525MHz
CH.7 162.550MHz
Audio
Maximum Power Output: 70W x 4 @ 2 ohm
USB
USB: 2.0 Full Speed
USB Port: 2.1A
USB Voltage: 5.0V
Maximum MP3/WMA Songs: 65535
Maximum MP3/WMA Folder: 255
Maximum Songs per Folder: 65535
Maximum USB Memory Size: 32G
Supported Format: FAT16/FAT32
Bluetooth
Specification: Bluetooth Version.
3.0+EDR (Enhanced Data
Rate)
Supported Profiles: A2DP (Advanced Audio
Distribution Profile)
aptX (CD Quality audio
bandwidth matching and
reproduction)
AVRCP 1.4 (Audio/Video
Remote Control Profile)
SPP (Serial Port Profile)
SSP (Simple Secure
Pairing)
Send/Receive Sensitivity: Class 2
22
CMS4
General
Power Supply Voltage: 14.4V DC (10.8 to 15.6V
allowable)
Grounding System: Negative Ground
Power When Off: 3.6mA
Note: Specifications and design are subject to
change without notice for further improvement.
Power Output:
18W × 4 RMS (4 Ω @14.4V
≤ 1% THD+N)
Signal to Noise Ratio:
72dB (reference: LPF 1W
into 4 Ω)

INSTALLATION AND WIRE CONNECTION

1. BEFORE STARTING

1. This set is exclusively for use in vessels with a negative
ground 12 V power supply.
2. Read these instructions carefully.
3. Be sure to disconnect the battery " " terminal
before starting. This is to prevent short circuits during
installation. (Figure 1)

2. INSTALLATION CAUTIONS

1. In order to avoid any interference, do not install the tuner module or control unit in the proximity of the
engine compartment.
2. The use of unauthorized parts can cause permanent damage to the unit.
3. Always check your wire connections to ensure proper installation before turning on the unit.
4. Consult with your nearest dealer for proper installation or if common parts need to be used. Seek
assistance if modifications or drilling holes to your vessel is needed.
5. Do not install the unit where it will be subjected to excessive moisture, dust, dirt, foreign particles or
vibration. Areas of high temperature from the engine, direct sunlight, heater or hot air should also be
avoided.
6. Do not install the unit in a location where it will interfere with the vessel operation, or it will injure the
passengers if there is a sudden or emergency stop.
3. OPTIONAL MARINE WIRED REMOTE INSTALLATION
The control unit should be mounted to a dry, clean and flat surface. Ensure the rear gasket is fully sealed to
the mounting surface without distorting the unit.
Dashboard
Screw
Hole
Trim Plate
Method 1
Battery
Figure 1
Dashboard
Screw Hole
Screw Hole
Mounting Bracket
Method 2
CMS4
23