Battery Replacement - Hornbach 6758657 Instructions De Montage

Bande lumineuse à led à capteur de mouvements sur 1 mètre alimenté par piles

Masquer les pouces Voir aussi pour 6758657:

Mode d'emploi (2 pages)

Table Des Matières

Table des Matières

Les langues disponibles

English

II.

30mm

a 60˚

Assembly instructions

Please read these instruc-

tions carefully and keep

Description

them safe for later use!

1 Movement sensor

Safety information

2 MAN/AUTO switch

• Electrical work and repairs must be

performed by a qualified electrician.

3 ON/OFF button

• During installation, always observe

the national installation regulations.

4 Battery box incl. 4 (separated)

• The luminaire must not be modified

batteries

in any way. Risk of electric shock and

accident.

5 Light strip

• This article is not a toy. Do not use in

nurseries.

• Do not look directly into the LED

beams.

• The light source of this luminaire

is not replaceable; when the light

source reaches its end of life the

whole luminaire shall be replaced.

II.

Assembly

Technical data

Caution: Do not attach the light

Battery type:

strip over sharp edges. Make sure

Voltage:

that the underground is flat or has a ra-

Rated power:

dius larger than 30 mm at angles above

Degree of protection: IP20

60°.

Colour temperature: 4000 K

Light Source:

1. Remove batteries. Cut the light strip

5 at the cutting mark to the desired

Size:

length.

Luminous flux:

2. Remove the self-adhesive tape at the

Sensor detection

back of the light strip.

distance:

3. Affix the light strip at the desired

location by pressing it lightly with the

fingers onto the surface.

4. Insert batteries (see IV.) In order to

Used symbols

install the battery box 4, remove the

Caution: Risk to health and the

3M adhesive tape and use the

product.

pre-installed velcro fastener at the

backside to install it on the wall.

Do not use outdoors or in damp

Caution: Fully unwind the light

environments.

strip before inserting the

batteries.

ENGLISH

III.

For use of batteries

• CAUTION! Explosion hazard when the

batteries are not replaced correctly.

• Only replace by batteries of the same

type. Pay attention to the correct

polarity.

• Do not expose batteries (battery pack

or inserted batteries) to excessive heat

from sunlight, fire, etc. Protect from

mechanical shocks. Keep dry and

clean. Keep out of reach of children.

• Do not open, disassemble, cut open,

or short-circuit batteries. Do not use

old and new batteries together.

• Observe the safety notes and other

notes on the battery and its packag-

ing.

• Remove leaking batteries and clean

the battery compartment thoroughly.

Avoid contact with eyes and skin.

IV.

Waste disposal

4x AAA 1.5 V

The pictogram with the crossed

6 V DC

out dustbin points to the require-

2.8 W

ment for separate disposal of

electrical and electronic appliances

(WEEE). Electrical and electronic appli-

LED –non-

ances can contain hazardous and envi-

replaceable!

ronmentally hazardous materials. Do

1000x8x2 mm

not dispose of this appliance as do-

130 lm

mestic waste. Hand it in at a collection

point for electrical and electronic waste.

approx. 4 m

By doing so, you will help to conserve

resources and protect the environment.

For further details, please consult your

local authorities.

Used batteries must be disposed of

properly. Battery selling stores and

municipal collection points offer special

containers for battery disposal.

Motion Sensor

Use the MAN/AUTO switch 2 to

change the mode of operation.

A. AUTO: The light strip switches

on automatically when move-

ment is detected within a sens-

ing range of 100

. After 30 sec-

onds the light strip switches off.

B. MAN: The light strip can be

turned on/off with the ON/OFF

button 3.

Note: Keep movement sensor 1 on

the light strip uncovered and free of

obstacles for proper functioning.