Important Safety Advice - EWT DANVILLE DNV20AB Mode D'emploi

EWT Opti-myst Inset Fires
Model: DNV20AB, DNV20BR, DNV20BL, DNV20CH
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Important Safety Advice:

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire,
electrical shock and injury to persons, including the following:
If the appliance is damaged, check with the supplier before installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings of a bath, shower or swimming pool.
Do not locate the heater immediately below a fixed socket outlet or connection box.
This appliance is not intended for use by children or other persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to
ensure that they do not play with the appliance.
Do not use this heater in series with a thermal control, a program controller, a timer or any other device that
switches on the heat automatically, since a fire risk exists when the heater is accidentally covered or displaced.
Ensure that furniture, curtains or other combustible material are positioned no closer than 1 metre from the
heater.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Although this heater complies with safety standards, we do not recommend its use on deep pile carpets or on
long hair type of rugs.
The appliance must be positioned so that the plug is accessible.
If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified
person in order to avoid a hazard.
Keep the supply cord away from the front of the heater.
WARNING: In order to avoid overheating, do not cover the heater. Do not place material or garments on the
heater, or obstruct the air circulation around the heater.
The heater carries a DO NOT COVER warning.
General.
Unpack the heater carefully and retain the packaging for possible future use, in the event of moving or returning the fire to
your supplier.
The fire incorporates a flame effect, which can be used with or without heating, so that the comforting effect may be enjoyed
at any time of the year. Using the flame effect on its own only requires little electricity.
The heater is designed for use inset into a 407mm (16") or 457mm (18") wide by 559mm (22") high fireplace opening or
freestanding - see also section 'Installation Instructions' .
A 2kw fan heater is discreetly positioned in the canopy of the fire provides heating in cold weather. Switching allows half
or full heat. A distance of 1 metre (39") must be maintained between the front of the heater and any surrounding furniture,
overhanging curtains or other obstrustions.
To reduce heat loss and to prevent any chimney up draft affecting the operation of your inset fire we recommend they the
chimney flue is sealed off.
Before connecting the heater check that the supply voltage is the same as that stated on the heater.
Please note: Used in an environment where background noise is very low, it may be possible to hear a sound which is related
to the operation of the flame effect. This is normal and should not be a cause for concern.
Electrical connection.
WARNING – THIS APPLIANCE MUST BE EARTHED.
This heater must be used on an AC ~ supply only and the voltage marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating instructions.
PLEASE RETAIN THIS USER'S GUIDE FOR FUTURE REFERENCE
Only use filtered tap water in this appliance.
Always ensure that the appliance is sitting on a level surface.
If you intend not using the appliance for longer than 2 weeks, drain the water from sump and water tank and dry the
sump.
Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.
The water tank, sump, sump lid, tank cap and air filters must be cleaned once every two weeks, particularly in hard
water areas.
The appliance should never be operated if the lamps are not working.
The lamps should be regularly inspected as described under 'Maintenance' and 'Changing lamps'.
6