Gemini PMX-03 Manuel D'instructions page 5

stay there, and the frequency will be killed. When you move
the selected KILL SWITCH to the center position the kill
function is not active, and the frequency will not be killed.
When you move the selected KILL SWITCH to the bottom
FLASH position and hold it there, the frequency will be
killed. Releasing the selected KILL SWITCH from the bot-
tom position will bring it back to the center position and the
frequency will no longer be killed.
5.
CROSSFADER SECTION: The CROSSFADER (20)
allows the mixing of one source into another. The left side
of the CROSSFADER (20) is CH 1 (19) while the right
belongs to CH 2 (31). You may also reverse this default by
switching the HAMSTER/REVERSE (11) switch. The
CROSSFADER (20) in your unit is removable and if the
need arises can be easily replaced. Your Gemini mixer
comes with an RG-45 (RAILGLIDE™) DUAL-RAIL
CROSSFADER. RAIL GLIDE™ crossfaders have internal
dual stainless steel rails that allow the slider to ride smooth-
ly and accurately from end to end. Also available is our is
the RG-45 PRO (RAIL GLIDE™) crossfader with a special
curve designed for scratch mixing. Just purchase one from
your GEMINI dealer and follow the instructions:
USER REPLACEABLE CROSS FADER
1. Unscrew the outside mixer
FACE PLATE screws and remove
the face plate. Then remove
FADER plate screws (B & C).
2. Carefully lift the fader and
unplug the CABLE (D).
3. Plug the new fader into the
cable and place it back in the
mixer.
4. Screw fader plate to the mixer
and replace the mixer FACE
PLATE.
Note: Do not apply pressure while using the Crossfader. Lightly glide
the Crossfader back and forth. Pressing down on the controls can
bend contacts and cause a loss of sound.
6. SLOPE CONTROL: The CROSSFADER SLOPE
SWITCH (12) allows you to adjust the kind of curve the
crossfader has. Flip the crossfader slope switch up to make
the slope steep and cutting (perfect for scratching). flip the
crossfader slope switch to make the slope gradual and gen-
tle.
7. HAMSTER CONTROL: The CROSSFADER REVERSE
SWITCH (11) allows you to reverse the crossfader so that
CHANNEL 2 (31) is controlled by the left side of the cross-
fader and CHANNEL 1 (19) is controlled by the right side of
the crossfader.
NOTE: When the CROSSFADER REVERSE SWITCH (11) is activated
(moved to the right), only the crossfader reverses. The Channel
Slides, Gain, Kill Switches and tonal controls do not reverse.
8. CUE: Cue facilitates the seamless blending of one
recorded track into another. Connecting a set of head-
phones to the HEADPHONES (8) jack allows you to moni-
tor either CHANNEL 1 or CHANNEL 2. Select CHANNEL
1 (19) by moving CUE FADER (18), located on the front
panel, to CUE 1 on the left. Listen to CHANNEL 2 by mov-
ing CUE FADER (18) to CUE 2 on the right. To mix both
Channels bring CUE (18) to the middle so that both tracks
may be heard. Use CUE VOLUME (9) to adjust the head-
phone volume without affecting the speaker-driven mix.
9. MIC SECTION: Connecting a microphone to the 1/4"
MIC JACK (10) allows voice amplification through the
mixer to the stereo through the MASTER RCA OUTPUTS
(3). This is controlled by the MIC VOLUME (16), HIGH (15),
LOW (14) rotary controls.
10. OUTPUT CONTROL SECTION: The level of the MAS-
TER OUTPUT (3) is controlled by the MASTER VOLUME
(13) rotary control.
11. VU METER: The VU METER (25) LEDs indicates the
MASTER RCA OUTPUT (3) in stereo. VU METER (25)
LEDs reflect the VOLUME (13), GAIN (24,32), HIGH
(23,33), MID (22,34) and LOW (21,35) rotary control adjust-
ments for each channel. The CHANNNEL SLIDES (19, 31)
also affect each of the VU METER (25) LEDs.
SPECIFICATIONS:
INPUTS:
DJ Mic......................................................................1.5 mV 1 kOhm Balanced
Phono........................................................................................3 mV 47 kOhm
Line.......................................................................................150 mV 10 kOhm
OUTPUTS:
Amp......................................................................................0 dB 1V 400 Ohm
Max.......................................................................................20V Peak to Peak
GENERAL:
Bass (Channels 1-2)..................................................................+12 dB/-36 dB
Mid (Channels 1-2).....................................................................+12 dB/-36 dB
High (Channels 1-2)...................................................................+12 dB/-36 dB
Gain (Channels 1-2)........................................................................0 to -20 dB
Frequency Response....................................................20 Hz-20 kHz +/- 2 dB
Distortion...............................................................................Less Than 0.02%
S/N Ratio.............................................................................Better Than 80 dB
Headphone Impedance........................................................................32 Ohm
Power Source Adapter........................................................115V/15V AC 0.5A
........................................................................................or 230V/15V AC 0.5A
Unit Dimensions........................................................W 10" x H 3.3" x D 10.25"
..........................................................................................(254 x 84 x 260mm)
Weight....................................................................................6.2 lbs ( 2.81 kg)
NOTE: SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE
WITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT.
(5)