Automatic Power-Off (Power Management) - Pioneer PDA-5003 Mode D'emploi

Masquer les pouces Voir aussi pour PDA-5003:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Automatic power-off
(POWER MANAGEMENT)
The plasma display is equipped with [POWER
MANAGEMENT] and [AUTO POWER OFF] functions;
when set, the function automatically switches the unit to
either standby mode or power off mode whenever a sync
signal is not detected (a warning message is displayed on
the screen before the functions operate).
Notes
÷ [POWER MANAGEMENT] settings are supported only when a
computer signal is input to INPUT1, INPUT2 or INPUT5 (PDA-
5003 only).
÷ The auto-power-off function can be used only in those cases
other than the inputs used in the preceding item.
÷ Always turn off the plasma display's main power switch when
not using the display for extended periods of time.
INPUT
MENU
2/3
SET
Display operating
Remote control unit
panel
1
Press the MENU button to display the menu screen.
MENU
PICTURE
SCREEN
:
CONTRAST
:
BRIGHTNESS
:
R.LEVEL
:
G.LEVEL
:
B.LEVEL
:
H.ENHANCE
:
V.ENHANCE
PICTURE RESET
2
Use the 2/3 buttons to select [SETUP].
[When computer signal is input to INPUT1, INPUT2
or INPUT5 (PDA-5003 only)]
MENU
PICTURE
SCREEN
POWER MANAGEMENT
CLAMP POSITION
SIGNAL FORMAT
INPUT
MENU
2/3
SET
INPUT1
SETUP
OPTION
0
0
0
0
0
0
0
INPUT1
SETUP
OPTION
:
OFF
:
AUTO
: V G A
:
[In all other cases]
MENU
PICTURE
SCREEN
AUTO POWER OFF
COLOR TEMP.
DNR
MPEG NR
CTI
PURECINEMA
COLOR SYSTEM
CHANGE
SET
3
Press the SET button to confirm selection of the
[POWER MANAGEMENT] or [AUTO POWER OFF].
The factory default setting is [OFF/DISABLE].
Each time the button is pressed, the setting alternates
as follows:
3 OFF/DISABLE
ON/ENABLE 2
÷ OFF/DISABLE.....
The display will continue in operating mode,
regardless of the presence/absence of an input sync
signal.
÷ POWER MANAGEMENT: ON.....
If a sync signal is not detected, a warning message is
first displayed for 8 seconds, after which the display
automatically enters the standby mode, and the ON
indicator flashes green. If a sync signal (*1) is input
again later, the plasma display automatically returns to
normal operating mode.
*1 Except when input signal is G ON SYNC or composite
SYNC.
÷ AUTO POWER OFF: ENABLE.....
If no sync signal is detected for 8 minutes or more, a
warning message will be displayed for 30 seconds,
after which the display's power will switch to power off
mode.
4
When the setup is finished, press the MENU
button to exit the menu screen.
Note
The [POWER MANAGEMENT] and [AUTO POWER OFF]
functions must be set individually for each input (INPUT1 to
INPUT5).
To return to operating mode:
÷ To return to normal operation from the [POWER
MANAGEMENT] function's standby mode, either operate
your computer, or press the INPUT button on the plasma
display or remote control unit.
÷ To return to normal operation from the [AUTO POWER
OFF] function's power off condition, press the STANDBY/
ON button on the plasma display or on the remote control
unit.
Operation
INPUT3
SETUP
OPTION
:
DISABLE
:
MIDDLE
:
MIDDLE
:
LOW
:
ON
:
OFF
:
AUTO
EXIT
MENU
27
En

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Pda-5004

Table des Matières