Pioneer PDA-5003 Mode D'emploi page 74

Masquer les pouces Voir aussi pour PDA-5003:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

System Settings
1
Select INPUT1, INPUT2 or INPUT5.
2
Press the MENU button to display the menu screen.
MENU
PICTURE
SCREEN
:
CONTRAST
:
BRIGHTNESS
:
COLOR
:
TINT
:
SHARPNESS
PICTURE RESET
3
Use the 2/3 buttons to select [SETUP].
MENU
PICTURE
SCREEN
AUTO POWER OFF
COLOR TEMP.
DNR
MPEG NR
CTI
PURECINEMA
COLOR DECODING
CLAMP POSITION
SIGNAL FORMAT
CHANGE
SET
4
Use the 5/∞ buttons to select [SIGNAL FORMAT],
then press the SET button.
MENU
PICTURE
SCREEN
AUTO POWER OFF
COLOR TEMP.
DNR
MPEG NR
CTI
PURECINEMA
COLOR DECODING
CLAMP POSITION
SIGNAL FORMAT
5
Use the 2/3 buttons to select the display mode.
SIGNAL FORMAT
SET
S E T
1 When the input signal has a refresh rate of 31.5 kHz
horizontal / 60 Hz vertical, pressing 2/3 will cause
the display mode to change alternately as follows:
When using INPUT1, INPUT5 or INPUT2 (PDP-
505CMX/PDP-50MXE10/PDP-50MXE11 only):
3 525p 2
3 WVGA 2
When using INPUT2 (PDP-504CMX/PDP-50MXE1/
PDP-50MXE1-S and PDP-434MCX/PDP-43MXE1/
PDP-43MXE1-S only):
3 VGA 2
20
En
INPUT1
SETUP
OPTION
0
0
0
0
0
INPUT1
SETUP
OPTION
:
DISABLE
:
MIDDLE
:
:
MIDDLE
:
LOW
:
ON
:
OFF
:
RGB
:
AUTO
:
:
VGA
EXIT
MENU
INPUT1
SETUP
OPTION
:
DISABLE
:
MIDDLE
:
:
MIDDLE
:
LOW
:
ON
:
OFF
:
RGB
:
AUTO
:
:
VGA
:
VGA
M
N U
EXIT
E
3 VGA 2
3 WVGA 2
2 When providing input signals with refresh rates of 45
kHz horizontal / 60 Hz Vertical, pressing the 2/3 buttons
causes the display mode to alternate as follows:
3 720-PC 2
÷ [720-PC] indicates resolution of 1280 x 720.
3 When the input signal has a refresh rate of 48.4
kHz horizontal / 60 Hz vertical, or 56.1 kHz
horizontal / 70 Hz vertical, pressing 2/3 will cause
the display mode to change alternately as follows:
3 XGA 2
3 PC AUTO 2
If the [PC AUTO] setting is selected, screen
resolution will automatically switch between [XGA]
and [WXGA] as required.
4 When the input signal has a refresh rate of 64 kHz
horizontal / 60 Hz vertical, 80 kHz horizontal / 75 Hz
vertical, or 91.2 kHz horizontal / 85 Hz vertical,
pressing 2/3 will cause the display mode to
change alternately as follows:
3 SXGA 2
Notes
÷ These settings are required only when providing input signals
with the following refresh rates: 1 31.5 kHz horizontal / 60 Hz;
2 45 kHz horizontal / 60 Hz vertical; 3 48.4 kHz horizontal / 60
Hz vertical or 56.1 kHz horizontal / 70 Hz vertical; 4 64 kHz
horizontal / 60 Hz vertical; 80 kHz horizontal / 75 Hz vertical or
91.2 kHz horizontal / 85 Hz vertical. Adjustment for other signal
frequency formats is performed automatically, so no manual
setting is required (the [SIGNAL FORMAT] message does not
appear).
÷ The [PC AUTO] setting supports automatic signal selection
only when using RGB separate SYNC inputs.
÷ When G ON SYNC or Composite SYNC signals are input,
selecting [PC AUTO] will cause the screen resolution to be set
to [XGA] only.
÷ When using G ON SYNC or Composite SYNC with WXGA
inputs, set [SIGNAL FORMAT] manually to [WXGA].
6
Press the SET button.
The setting is stored in memory and the screen
returns to that shown in step 4.
7
When a component other than a computer is
connected, use the 5/∞ buttons to select [COLOR
DECODING] (INPUT1, INPUT2 or INPUT5).
MENU
PICTURE
SCREEN
AUTO POWER OFF
COLOR TEMP.
DNR
MPEG NR
CTI
PURECINEMA
COLOR DECODING
CLAMP POSITION
SIGNAL FORMAT
8
Press the SET button repeatedly to select the
input signal format.
3 750p 2
3 WXGA 2
3 SXGA+ 2
INPUT1
SETUP
OPTION
:
DISABLE
:
MIDDLE
:
:
MIDDLE
:
LOW
:
ON
:
OFF
:
RGB
:
AUTO
:
:
VGA

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Pda-5004

Table des Matières