Positioning The Range; Installation Requirements; Installation Clearances - Heartland 5210 Instructions D'installation Et D'utilisation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Positioning the Range

1. When the range is fully assembled, recheck all electrical connections especially between the exhaust hood and the back of the
range. As well, check that all nuts and bolts have been tightened.
position.

Installation Requirements

Put both hands on the trim and carefully push the range into place. Make sure floor is clear of all debris. Don't forget to plug in the
Due to continuing product improvements, AGA Marvel reserves the right to amend specifica-
tions without notice. Please contact AGA Marvel for the most up to date information, as it applies to product
being purchased, or download latest Site Preparation Specifications from www.heartlandapp.com.
See closet installation instructions.
Page 2 under "Gliders"). Using a 5/16 (8mm) open end wrench turn the adjusting screw clockwise to raise up the corner, and counter-
Dimensions
27-1/2"
11-3/8"
(70 cm)
Ensure the unit is perfectly level, or utensils may fall of during cooking.
3-7/8"
(29 cm)
( 10 cm)
iand levelled, you may want to place coasters under the teflon gliders of each leg to protect the floor. Remove the coasters when
moving the range for cleaning or servicing.
62-3/8"
(159 cm)

Installation Clearances

If the range must stand beside a refrigerator, it is important for proper air circulation that there be at least 5" of space between
36-1/8"
(92 cm)
the two appliances.
Do not install range closer than 1/2" from adjacent surfaces.
28"
29-3/4"
surface units should be avoided. If there is existing closet storage space have at least 30 1/4" (768 mm) of clearance.
(72 cm)
(76 cm)
3 3/4" / 9.5 cm
(see Fig 3)
For best cooking results, your range should be level. This can be checked with a carpenter's level on top of the cooking
surface and across the oven rack. If levelling is required, adjust the leveller screws under one or more of the legs (see
"Positioning the Range" step 5).
Rough In
Measurements
Range Hood Outlet 3-1/2" x 10-1/2"
(
8.9 x 26.7 cm )
66 3/4"
(169.5 cm)
with std cresting 56"
(142 cm)
62 7/8"
(160 cm)
without cresting
Receptacle Location
(use flush mounting
12"
(30.5 cm)
juction box)
5"
(13 cm)
Rough in Opening
Model 4210 shown
Surface adjacent to cook top-left (48")
Surface adjacent to cook top (30")
Cook top to underside of adjacent closets ...18" (457 mm)
Maximum depth of overhead closets ............13" (330 mm)
Maximum height of counters ..........................36" (914 mm)
The clearances in the table are also stated on the rating plate located at back of stove.
Models 4200/4210
Range Hood
13 3/4 "
Outlet : 3 1/4"x 10"
35 cm
8.3 Cm x 25.4 cm
56"
142.3 cm
Gas Inlet-1/2 NPT
Power In
(
direct connection)
8 ft (2.4m) cord
36 1/8"
supplied
92 cm
Exhaust
Hood In
34 "
86.4 cm
.
29 3/4"
76 cm
(6" clearance to any
combustible wall)
13-3/4"
(35 cm)
13"
(33 cm)
cabinet depth
30-1/4"
6" (16 cm)
(77 cm)
24"
(61 cm)
counter
depth
36"
(92 cm)
Model 4210 30" Installation Clearance
2
Installation Clearances
1" (25mm)
0" (0 mm)
(see "Installation Clearances" diagram)
(page 2 of 2)
Help Desk
800-223-3900
14"
(36 cm)
29-1/2"
(75 cm)
66 1/4"
168.3 cm
43-3/4"
(111 cm)
62 3/8"
with oven
159 cm
0" clearance
door open
to the back
3" (7.6 cm)
52"
(132 cm)
with bottom drawer fully open
Fig 3 Installation Clearances
0
0
min
30 1/4"
768 mm
min 18"
0
457 mm
0
Min 18"
0
(46 cm)
0
max
36 "
914 mm
© 2010 AGA MARVEL
Surface adjacent to cook top-right (48") .......0" (0 mm)
Surface adjacent to warming oven ...............0" (0 mm)
Cook top to underside of closets .... 30 1/4" (768 mm)
Maximum depth of counters ..................24" (610 mm)
Rear clearance 0" .........................................(0 mm)
5
min
30 1/4"
77 cm
1"
2.5 cm
min
36 "
92 cm
Model 5210 48" Installation Clearance
0
min 18"
46 cm
0

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

4210

Table des Matières