Listening To Radio Programs - Denon DRA-F100 Mode D'emploi

7

LISTENING TO RADIO PROGRAMS

(Check the connections on pages 5 and 6.)
TUNING
Receiver
(DRA-F100)
B
REMOTE SENSOR
SYSTEM
ON / STANDBY
PHONES
1
Example: Tuning in FM 87.5 MHz
(AM stations are tuned in using the same procedure.)
Set the VOLUME control on the
receiver to the minimum position,
1
then press the SYSTEM power
operation switch (SYSTEM ON/
STANDBY) to turn on the power.
Press the BAND button on the
2
receiver to select the FM band.
Use the TUNING UP and DOWN
buttons to tune the frequency to
3
87.50. Once the frequency is tuned
in, adjust the volume to the desired
level using the VOLUME control.
Auto Tuning
• When one of the TUNING buttons is pressed, the frequency changes in steps of 50kHz in the FM band, 9kHz in the AM band.
• If one of the TUNING buttons is held in for over 1 second, the frequency continues to change when the button is released (auto
tuning) and stops when a station is tuned in. Tuning will not stop at stations whose reception is poor.
• To stop the auto tuning function, press the UP or DOWN button once.
Presetting AM and FM Stations
Example: Presetting FM 87.5 (currently tuned in) at preset number 3
Press the MEMORY button.
4
The indicator flashes for
MEMO
10 seconds.
Use the TUNING UP and DOWN
buttons to call out the number at
which you want to preset the
5
station (3), or simply press the
corresponding number button "3"
on the remote control unit.
Press the MEMORY button while
6
the MEMO indicator is flashing.
Up to 40 AM or FM stations can be preset using this procedure.
All manuals and user guides at all-guides.com
3,5 2
PERSONAL COMPONENT SYSTEM / AM-FM STEREO RECEIVER DRA-F100
MHz CH
TIMER
TUNED STEREO AUTO
TREBLE
TUNING MONO / BASS BALANCE
DOWN UP BAND STEREO
TIMER DISPLAY MEMORY FUNCTION
L R
4,6
SYSTEM
ON / STANDBY
BAND
TUNING
DOWN UP
TUNED
MEMORY
TUNED
TUNING
DOWN UP
TUNED
MEMORY
TUNED
VOLUME
MHz
This lights when a station is tuned in.
MHz
STEREO AUTO
Flashes
MHz CH
STEREO AUTO MEMO
Flashes
"P" flashes
MHz CH
STEREO AUTO MEMO
Flashes
"P3" lights
MHz CH
STEREO AUTO
Auto Preset Memory Function
(FM ONLY)
This function automatically stores the FM stations which c
preset memory. Also note that the channel memories ca
stored with this function.
Connect the FM antenna and set it
1
so that FM stations can be
received.
Press the SYSTEM power operation
switch (SYSTEM ON/STANDBY) to
2
turn on the power while holding in
the MEMORY button.
Searching begins automatically, and
stations are stored in the preset
memory in order, beginning from
3
channel 1 (The operation
automatically stops once 40
stations have been set in the
memory.)
NOTES:
• In addition to the reception frequency, the reception mo
presetting stations.
• If a station is preset at a number where a station is alread
• The preset memory is not cleared immediately when t
unplugged for an extended period of time. If this happens
Listening to Preset Stations
The preset stations can be recalled using the number butto
Also, if the following operation is performed when the syst
is played. (Auto on function)
Example: Listening to the station preset at number 3
(This operation is only possible from the rem
Press the TUNER button on the
1
remote control unit.
Press button "3" on the remote
2
control unit.
Refer
SYSTEM
ON / STANDBY
POWER 8
SLEEP
6
EDIT RA
TIME
SIDE A/B
q
PROGRAM CA
w
1