Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Press button ＊ and then button 7 — The control unit transmits remote keypad learning data
Press button ＊ and then button 2 — Panic alarm function on
Press button ＊ and then button 5 — Panic alarm functions off (default)
Press button ＊ and then button 6 — Change keypad code
Enter the old remote keypad code and press the button
Enter the new 4-digit keypad code and press the button #.
Press button
Press button ＊ and then button 8 — Arming mode without user code on.
Press button ＊ and then button 9 — Arming mode with user code on (default).
Procedura di apprendimento
Step 1: Set the control unit to learn mode.
Step 2: Add the remote keypad in the control unit:
Test mode learning
I. Set the remote keypad in Test mode by entering the keypad code (pre-set: 0000) followed by button＊. The amber
state LED lights up and a long beep will sound.
II. Press button ＊ and then button 7. The remote keypad will generate a long beep.
<
N
O
T
E
>
<
N
O
T
E
>
If the remote keypad does not generate a long beep, it means that no learning data has been sent to the
control unit; press button * and then button 7 to send the learning data again.
III. The respective information will be shown if the control unit receives the learning data. Refer to the control unit instruction
manual to complete the learning procedure.
IV. After having received the remote keypad signal, the control unit will send a confirmation to the remote keypad. The
remote keypad will beep three times to confirm that validation was received.
Learning with double button:
I. In normal operating mode, press buttons # and ＊ together. The remote keypad will generate a long beep.
<
N
O
T
E
>
<
N
O
T
E
>
If the remote keypad does not generate a long beep, it means that no learning data has been set to the
control unit; press button # and * to send the learning data again.
II. The respective information will be shown if the control unit receives the learning data. Refer to the control unit instruction
manual to complete the learning procedure.
III. After having received the remote keypad data, the control unit will send a confirmation to the remote keypad itself. The
remote keypad will beep three times to confirm that validation was received.
<
I
M
P
O
R
T
A
N
T
N
O
T
E
>
<
I
M
P
O
R
T
A
N
T
N
O
T
E
>
If the remote keypad does not beep three times, run the learning procedure again.
Step 3: After run the remote keypad learning procedure, set Walk Test mode on the control unit, keep the remote keypad in the
desired position and send the learning data to the control unit to check that it is within the range of the control unit signal. To send
learning data, press button ＊ and then button 7 in Test mode or press buttons # and ＊ in normal operating mode.
Step 4: Once the correct operation of the remote keypad in the chosen position has been checked, proceed with the installation
following the procedure described below.
Step 5: Modify the local code to access test mode, if necessary:
I.
With the keypad in Test mode, press button ＊ and then button 6: the keypad will generate a long beep.
II. Enter 0000 (default code).
III. Press button
IV. Enter the new 4-digit code.
V. Press button #: the remote keypad will generate a long beep. The new code is enabled.
Step 6: Press the button twice
Installazione
To mount the remote keypad:
I
I
.
.
Remove the front lid.
I
I
.
Using the two assembly holes of the rear cover as a template, mark the position of the holes in the more suitable
I
I
.
position.
I
I
I
.
Insert the anchor bolts if the device is fixed to plaster or bricks.
I
I
I
.
I
V
.
Screw the remote keypad to the anchor bolts.
I
V
.
V
.
Close the front lid.
V
.
Ripristino dei valori di fabbrica:
The remote keypad can be reset with the default values and restarted if the keypad code is forgotten or the remote keypad displays
a problem.
Step 1 Remove the battery.
Step 2 Hold button 3 pressed and insert the battery.
Step 3 Hold button 3 pressed until the keypad beeps 3 times.
Step 4 Release button 3: the reset procedure is done.
twice — Exit Test mode.
: the keypad will generate a long beep.
to exit Test mode and complete the installation.
Publicité
Table des Matières
