Technical Data - EINHELL BT-LC 700/1 D Mode D'emploi D'origine

Anleitung_BT_LC_700_1_D_SPK1:_
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.

5. Technical data

AC motor:
Power P:
Protection type:
Idle speed n :
0
Saw blade:
Number of teeth:
Max. cutting capacity (reversing cut):
Min. cutting capacity:
Max. material length:
Min. material length:
Weight:
Operating mode S6 20%: Continuous operation with
idling (cycle time 10 minutes). To ensure that the
motor does not become excessively hot it may only
be operated for 20% of the cycle at the specified
rating and must then be allowed to idle for 80% of
the cycle.
6. Before starting the machine
(Fig. 1-6)
Do not start the machine until you have made
yourself familiar with these operating
instructions and all the safety instructions. If
you have no experience in handling these
machines, you should obtain assistance from
an experienced person.
Unpack the saw and check it for damage which
may have occurred in transit.
The machine may only be used outdoors. The
machine must be placed on a horizontal, even
base and be firmly anchored to the ground using
the mounting holes (13) in the machine foot. The
ground around the machine must be clear of
waste, slippery areas and stumbling blocks.
All covers and safety equipment must be properly
installed and the saw blade must run freely.
Check the entire machine and al cables for any
signs of transport damage.
28.02.2011 9:51 Uhr
Check that the saw blade is secured, not dirty,
undamaged and sharp. Sharpen or replace blunt
saw blades.
Check that all the screw connections are tight.
Check the splitter inserts (18) for signs of wear
and replace them if necessary.
The feed cradle (6) must be returned to its original
position automatically by the spring (10).
Check the machine for any foreign bodies that
may be catapulted out of it.
The power source must be protected by an RCCB
with a fault current of 30 mA.
400 V 3 ~ 50 Hz
Check that the voltage on the rating plate is the
4500 W S6 20%
same as your supply voltage before you connect
IP 54 the machine to the power supply.
Important: It is essential that you check the
1440 rpm
direction in which the motor (1) turns. To do this,
Ø 700 x Ø 30 mm
switch the motor on and off briefly. The saw blade
64
must turn clockwise when viewed from the left-
270 mm hand side (see directional arrow on the saw
blade). If this is not the case the direction of
25 mm
rotation must be corrected using the phase
1000 mm
converter on the connection plug. To do this, turn
300 mm
the phase converter (15) in the connection plug
83 kg through 180° using a screwdriver. (see Fig. 4)
Important: It is essential that other persons
remain a safe distance from the saw whilst it is
operating.
Do not attempt to saw more than one piece of
wood or bundles of wood at the same time – this
poses a serious risk of injury. Place bent pieces of
wood in the feed carried so that the side that is
bent outwards faces the saw blade.
The feed carriage (6) for the wood is fitted with
hooks (19) that prevent the wood from turning.
Before you press the ON/OFF switch (7), make
sure that the saw blade (4) is fitted correctly and
that the machine's moving parts run smoothly.
Before using the saw you must adjust the transit
lock. To do this, swing the transit lock (11) to the
outside of the saw until the hole is over the screw
thread and then secure it with the screw (14). The
transit lock with supporting foot (11) now prevents
the feed carriage (6) pivoting away to the outside
with the wood.
Seite 19
GB
19