C O N N E C T I O N S O V E R V I E W; Usb O U Tput - Gemini CDMP-7000 Mode D'emploi

c o n n e c t i o n s o v e r v i e w

r e a r v i e w
N A
PoweR
Plug in the power cord of the CDMP-7000 into the AC IN
(A). Press the POWER OFF/ON (N) switch to power the
unit on.
R cA PHono / Line i nP UTS
The CDMP-7000 comes with two (2) stereo convertible
LINE/PHONO RCA INPUTS (K) that accept standard ste-
reo RCA connections. The two PHONO/LINE SWITCHES
(J) allow you to convert the RCA input connection be-
tween a PHONO (turntable) input or a LINE level (MP3,
CD, cassette deck, etc.) input. When switched to the PHO-
NO position, you may use any turntable with a magnetic
cartridge. Remember to connect your ground wire to the
GROUNDING SCREW (M) or there may be a system hum.
AUX in P UTS
The CDMP-7000 comes with two (2) stereo aux inputs.
AUX1 (I) is a stereo line-level RCA input and AUX2 (H) is a
stereo 1/8" input. Any line-level device (MP3, CD, cassette
deck, etc.) can be plugged into AUX1 and AUX2.
mi c in PUTS
The CDMP-7000 comes with two (2) mic inputs: one 1/4"
mic input and one XLR / 1/4" combo jack. The 1/4" mic in-
put accepts balanced or unbalanced connections. The XLR
/ 1/4" combo jack (L) accepts balanced XLR connections
or balanced/unbalanced 1/4" connections. The MIC VOL-
UME (46) control on the front panel controls the volume
of the mics connected.
*NOTE: It is advised to use a balanced 1/4" cable for less
noise and a stronger signal.
USB inPUT
The CDMP-7000 has a USB INPUT (G) designed to receive
audio from a computer (Mac/PC). Connect a USB cable
(not included) from one of your computer's USB ports to
the CDMP-7000's USB INPUT (G). To use the CDMP-7000
as your computer's audio device, select the device on your
computer's audio settings.
9
B C D E F G H
R cA Li ne oU TPU TS
The CDMP-7000 contains three different stereo RCA out-
puts: REC, MASTER and BOOTH (C). The MASTER output
connects the unit to your main amplifier. The RECORD out-
put can be used to connect the mixer to the record input
of a recording unit, thus enabling recording of a mix. The
BOOTH output can be used as an output source for moni-
tors or booth playback.
If connecting the CDMP-7000 through a receiver, the
RCA connection can be insterted into the CD AUX INPUT
JACKS on a receiver. If there are no CD nor AUX INPUTS
use any line level (not phono) inputs.
BA LA n c e d X LR oUTP UT
The XLR BALANCED OUTPUT (B) section has LEFT and
RIGHT XLR outputs for balanced operation of stereo outputs.
c d1 /c d2 oU TPUT
The CD1/CD2 stereo RCA outputs (D) allow the two media
players to be feed directly to an external mixer individually,
bypassing the mixer section of the CDMP-7000.

USB o U TPUT

Plug in the included USB cable into the USB OUT (F) on
the rear panel. Plug the other end of the USB cable into
any available USB port on your computer. This will enable
use of the CDMP-7000 in MIDI mode.
d ig iTA L o UTPU TS
Plug a S/PDIF cable (not included) into the DIGITAL OUT
on the CDMP-7000 (E) and into any DIGITAL IN port on
any device. This will send the digital audio to that input.
Possible applications include using the DIGITAL OUT to
record or to feed to a DAW (Digital Audio Workstation).
H e AdP Ho ne oUT PUTS
The CDMP-7000 contains two headphone outputs: one
1/4" headphone input and one 1/8" headphone input. The
HEADPHONE OUTPUTS (O) allow cueing of music before
playback through the master outputs.
M
I J K J
-
c d m p 7 0 0 0 m a n u a l • g e m i n i d j
L
.
c o m