Jenn-Air JDTSS243GX Guide D'utilisation page 5

OPTIONS
Raises the temperature with the power of
steam before final rinse to help enhance
shine, finish and reduce glass spots.
For added convenience, use for washing a
small load of dishes in the top rack to help
keep the kitchen continuously clean.
Sanitizes dishes and glassware in
accordance with NSF International NSF/
ANSI Standard 184 for Residential
Dishwashers. Certified residential
dishwashers are not intended for licensed
food establishments. Only sanitizing cycles
have been designed to meet the
requirements of the NSF/ANSI 184
performance standard for soil removal and
for sanitization efficacy. There is no
intention, either directly or indirectly, that all
cycles on a NSF/ANSI 184 certified
dishwasher meet the NSF/ANSI 184
performance standard for soil removal and
for sanitization efficacy.The Sani indicator
glows at the end of the cycle if the Sani
Rinse option was successfully completed. If
the indicator does not activate, it is probably
due to the cycle being interrupted.
Dries dishes with heat. This option with the
use of rinse aid will provide the best drying
performance. Plastic items are less likely to
deform when loaded in the top rack. Turn
Precision Dry
+
Runs the dishwasher at a later time or
during off-peak electrical hours. Select a
wash cycle and options. Press 4 Hour Delay.
Press START/RESUME. Close the door
firmly. NOTE: Anytime the door is opened
(such as, to add a dish), the START/
RESUME button must be pressed again to
resume the delay countdown.
Avoids unintended use of the dishwasher between cycles, or cycle and option changes during a cycle.
To turn on Lock, press and hold CONTROL LOCK for 3 seconds. The Control Lock light will stay on for a short time, indicating
that it is activated, and all buttons are disabled. If you press any button while your dishwasher is locked, the light flashes 3
times. The dishwasher door can still be opened/closed while the controls are locked.
To turn off Lock, press and hold CONTROL LOCK or 3 seconds. The light turns off.
Control
®
off for an air dry.
Purpose Comments
To start or If the door is opened during a cycle or power is interrupted, the Start/Resume indicator
resume a wash flashes. Press START/RESUME and push the door firmly closed within 3 seconds.
cycle. NOTE: If the door is not closed within 3 seconds, the Start/Resume indicator will flash, an
audible tone will be heard, and the cycle will not start.
To reset any Press CANCEL/DRAIN to reset any control selections made.
cycle or options
during
selection. See "Canceling a Cycle After Dishwasher Is Started" and "Changing a Cycle After
To cancel a Dishwasher Is Started" sections in the full online User Guide.
wash cycle
after it has
started.
CAN BE WHAT IT DOES
SELECTED
WITH
Sensor Wash Raises main wash
temperature from
Cookware/
105°F to 140°F (41°C
Bakeware
to 60°C), steam clean
Normal
before rinsing, final
Tableware
rinse temperature
140°F to 155°F (60°C
to 68°C).
Available Slightly faster wash for
with any smaller loads
cycle
Sensor Wash Raises main wash
temperature from
Cookware/
105°F to 140°F (41°C
Bakeware
to 60°C) and the final
Normal
rinse from 140°F to
Tableware
155°F (60°C to 68°C).
Top Rack
Wash
Available Activates the heating
with any
element at the end of
cycle except
the wash cycle to
Refresh/
speed drying times.
Rinse
The option defaults to
ON when any cycle is
selected except for
1 Hour Wash.
Available Delays the start of a
with any
cycle up to 4 hours
cycle
ADDED TIME TO CYCLE
TYPICAL MAX
78 100
-7 -30
53 73
44 52
240 240
.
ADDED
WATER
GALLONS
(LITERS)
0 - 3.9
(0 - 14.9)
0
0 - 3.0
(0 - 11.2)
0
0