Stanley D 200/8/24 Manuel Utilisateur page 20

GENERAL WARNINGS
When using air-powered accessories, always wear safety clothes.
Keep the work area free and always maintain a stable position.
Do not allow inexpert persons to use tools without suitable supervision. Keep children and animals at a distance from the work area;
improper use of compressed air may cause serious injuries.
WASHING SPRAY GUN
TECHNICAL DATA Max. pressure: 8 bar
INSTRUCTIONS FOR USE Fill the bowl (1), screw it to the body of the gun (2) and then connect the air hose to the inlet fitting (3). Press lever (4)
to spray the liquid. Adjust the size of the jet required using the ring-nut (5) and then secure this with the rear ring-nut (6). (A – B)
WARNINGS Always hold the gun horizontal during use in order to improve suction of the liquid in the bowl. Do not spray harmful substances
without wearing a mask and safety goggles.
INFLATION GUN
TECHNICAL DATA Max. pressure: 8 bar
INSTRUCTIONS FOR USE Connect the air hose to the inlet fitting (1) on the gun. To inflate the tire and check pressure, insert the fitting (2) in
the valve of the tire holding down the lever (3) on this; following insertion, release the lever (3). With the gauge facing you, read the pressure;
for inflation, press the lever (4) fully for a few seconds and then release it; repeat the operation until you have obtained the pressure required as
shown by the needle on the dial of the gauge. For deflation, release the lever (4) and press the button (5) with your thumb until all the air has been
expelled. (C – D).
WARNINGS Never exceed the inflation pressure recommended in the instructions for use of the object to be inflated. Protect the gauge against
impacts. In the case of impacts, check calibration.
BLOWING GUN
TECHNICAL DATA Max. pressure: 8 bar
INSTRUCTIONS FOR USE Connect the air hose to the inlet fitting (1) on the gun. Direct the nozzle towards the area or object to be blown and
press the lever (2). The flow of air can be adjusted by regulating pressure on the lever (2).
AIR BRUSH FOR PAINTING
TECHNICAL DATA Recommended operating pressure: 3 bar
INSTRUCTIONS FOR USE
AIR BRUSH WITH GRAVITY TYPE BOWL (4.1) Screw the bowl (1) to the body of the gun (3). Fill the bowl with paint (1) and close it with the lid
(4). Make sure that the vent valve (5) is open.
AIR BRUSH WITH LOWER BOWL (4.2) Screw the bowl (10) to the body of the gun (3) and secure tightly with a wrench.
Fill the bowl (11) with paint and fit it on the cover (10); fasten with a quarter turn to the right.
Connect the air hose to the inlet fitting (6) on the gun and adjust the pressure (3 bar) from the compressor.
Use the rear ring-nut (7) to adjust the amount of paint to be sprayed (tighten if you are using more fluid paints, open in the case of thicker paints)
and the side ring-nut (8) to regulate the size of the jet. (E-F / G-H). Direct the front perforated head of the nozzle (2) so that it is perpendicular to
the direction of painting. Prior to effective use, practice on a test material until you have obtained optimal adjustment and effect. Never leave paint
inside the bowl in order to use this subsequently as this may cause irreparable damage to the precision parts of the air brush. After use, always
clean the inside the air brush thoroughly, filling the bowel with pure solvent and spraying this without polluting the environment (spray on a rag or
absorbing surface) until there is no trace of the paint used in the jet of solvent sprayed. Clean the external parts of the gun stained by the paint
used with a rag dipped in solvent.
For more thorough cleaning, completely unscrew the rear ring-nut (7) and, taking care not to lose the internal spring, remove the needle of the
nozzle; the loosen the front ring (9) and remove the perforated head of the nozzle (2) and unscrew the nozzle with a wrench; put all the components
in a container with pure solvent for a number of hours; dry the components carefully and then carry out the above procedure in reverse order in
order to re-assemble all the parts.
WARNINGS Do not use the paint gun in a closed environment without ventilation. Do not use the air brush without wearing a safety mask.
SPIRAL CORD
TECHNICAL DATA Max. pressure: 8 bar
INSTRUCTIONS FOR USE OF CORD WITH FAST DISCONNECTS
Connect the end of the cord fitted with connector (1) to the compressor; connect the other end fitted with connector (2) to the air-powered tool. To
insert the connector (2) in the tool, push until it clicks in place.
To detach the cord, grasp the tool firmly with one hand and the ring-nut of the connector (2) with the other and pull in the opposite direction. If this
operation is difficult, make sure that you have vented all the air from the cord. (I – L)
WARNINGS Before connecting or disconnecting a tool or the cord, make sure that you have switched off the compressor.
The cord must not be crushed or bent as it could be pierced.
7
GB
1
2
3
4
5