Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

User Instructions
®
TitraStir
Titration Stand - Assembly Instructions
Specifications
Stirring speed
Largest stirring magnet size
Power requirements
Operating temperature
Storage temperature
Relative humidity
Maximum altitude
Pollution degree
Dimensions
Protection Class
Installation category
Safety information
Approximately 300 rpm at 60 Hz; 250 rpm at 50 Hz
2 inches
Model 19400-00: 115 VAC ±10%, 50 - 60 Hz, 20 VA maximum
Model 19400-10: 230 VAC ±10%, 50 - 60 Hz, 20 VA maximum
5 to 40 °C (41 to 104 °F) indoor use
–2 to 60 °C (28 to 140 °F)
Maximum relative humidity 80% for temperatures up to 31 °C (88 °F), decreasing linearly to 50%
relative humidity at 40 °C (104 °F)
2000 m (6562 ft)
2
Case: 22.8 x 15.2 x 9.6 cm (9" x 6" x 3")
Rod Height: 22.6 cm (10.5")
I
II
The manufacturer is not responsible for any damages due to misapplication or misuse of this
product including, without limitation, direct, incidental and consequential damages, and disclaims
such damages to the full extent permitted under applicable law. The user is solely responsible to
identify critical application risks and install appropriate mechanisms to protect processes during a
possible equipment malfunction.
Please read this entire manual before unpacking, setting up or operating this equipment. Pay
attention to all danger and caution statements. Failure to do so could result in serious injury to the
operator or damage to the equipment.
Make sure that the protection provided by this equipment is not impaired. Do not use or install this
equipment in any manner other than that specified in this manual.
Use of hazard information
Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death
or serious injury.
Indicates a potentially or imminently hazardous situation which, if not avoided, could result in
death or serious injury.
Indicates a potentially hazardous situation that may result in minor or moderate injury.
Indicates a situation which, if not avoided, may cause damage to the instrument. Information that
requires special emphasis.
N O T I C E
D A N G E R
W A R N I N G
C A U T I O N
N O T I C E
1940088
1

Publicité

Table des Matières
loading

Sommaire des Matières pour Hach TitraStir

  • Page 1 User Instructions 1940088 ® TitraStir Titration Stand - Assembly Instructions Specifications Stirring speed Approximately 300 rpm at 60 Hz; 250 rpm at 50 Hz Largest stirring magnet size 2 inches Model 19400-00: 115 VAC ±10%, 50 - 60 Hz, 20 VA maximum Power requirements Model 19400-10: 230 VAC ±10%, 50 - 60 Hz, 20 VA maximum...
  • Page 2: Precautionary Labels

    The Digital Titrator and titrator cartridge are not part of the TitraStir stand but are shown to demonstrate how they are installed. There is a slot in the side of the Titrator/Electrode holder to accommodate the delivery tube. A ½-inch wrench can be used to moderately tighten the support rod assembly in the titration stand.
  • Page 3 Titrator cartridge 11. Power cord connection Digital titrator 12. Power switch Titrator installation knob 13. Titrastir base Titrator/electrode holder assembly Cleaning D A N G E R Electrocution hazard. Remove all power from the isntrument before this maintenance task is started.
  • Page 4: Replacement Parts

    B-4840 Welkenraedt, Belgium Tel. +49 (0) 211 5288-0 Fax (970) 619-5150 Tel. +32 (0) 87 899 799 Fax +49 (0) 211 5288-143 hachflowsales@hach.com Fax +32 (0) 87 899 790 E-mail: info@hach-lange.de www.hachflow.com www.flow-tronic.com www.hach-lange.com © Hach Company/Hach Lange GmbH, 2013 07/2013, 4ed...
  • Page 5: Caractéristiques

    Instructions d'utilisation 1940088 ® Station de titrage TitraStir - Notice d'assemblage Caractéristiques Vitesse de rotation Environ 300 tr/min à 60 Hz ; 250 tr/min à 50 Hz Taille d'aimant de rotation 2 pouces maximale Modèle 19400-00 : 115 V c.a. ± 10 %, 50 - 60 Hz, 20 VA maximum Alimentation requise Modèle 19400-10 : 230 V c.a.
  • Page 6: Assemblage

    Le titrateur numérique et la cartouche du titrateur ne font pas partie de la station TitraStir mais sont indiqués sur la figure pour illustrer la façon dont ils sont installés. Le support de titrateur/d'électrode comporte une fente conçue pour accueillir le tube de sortie.
  • Page 7: Nettoyage

    Cartouche du titrateur 11. Branchement du cordon d'alimentation Titrateur numérique 12. Interrupteur marche/arrêt Molette d'installation du titrateur 13. Base du TitraStir Support de titrateur/d'électrode Nettoyage D A N G E R Risque d'électrocution. Coupez l'alimentation de l'appareil avant d'effectuer cette tâche de maintenance.
  • Page 8: Pièces De Rechange

    B-4840 Welkenraedt, Belgium Tel. +49 (0) 211 5288-0 Fax (970) 619-5150 Tel. +32 (0) 87 899 799 Fax +49 (0) 211 5288-143 hachflowsales@hach.com Fax +32 (0) 87 899 790 E-mail: info@hach-lange.de www.hachflow.com www.flow-tronic.com www.hach-lange.com © HACH Company/Hach Lange GmbH, 2013 07/2013, 4ed...

Ce manuel est également adapté pour:

Titration stand

Table des Matières