Macurco GD-6 Instructions D'utilisation page 14

Selecting Buzzer Option – "bUZ"
To select the Buzzer Configuration, in normal mode, press the Next button twice to get to "Con" or the Configuration menu. Then press
the Enter button to enter the Con menu. The fourth selection is the "bUZ" or Buzzer setting. Press Next three times to get to "bUZ"
then press Enter. If the display is "On" press Next to turn it "OFF" (flashing) then press Enter to confirm the change (solid) and press
Enter again to return to "bUZ" in the Con menu. Press Next until "End" is displayed then press Enter to return to normal operation.
Selecting Alarm Relay Setting – "ArS"
To select the Alarm Relay Setting, in normal mode, press the Next button twice to get to "Con" or the Configuration menu. Then press
the Enter button to enter the Con menu. The fifth selection is the "ArS" or Alarm Relay Setting. Press Next four times to get to "ArS"
then press Enter. If the display is "dIS" (disabled) press Next to change it to 5, 10, 15, 20 or 25% LEL (flashing) then press Enter to
confirm the change (solid) and press Enter again to return to "ArS" in the Con menu. Press Next until "End" is displayed then press
Enter to return to normal operation.
Selecting Alarm Relay Configuration – "Arc"
To select the Alarm Relay Configuration, in normal mode, press the Next button twice to get to "Con" or the Configuration menu.
Then press the Enter button to enter the Con menu. The sixth selection is the "Arc" or Alarm Relay Configuration. Press Next five
times to get to "Arc" then press Enter. If the relay is "nO" (normally open) press Next to turn it to "nC" (flashing) then press Enter to
confirm the change (solid) and press Enter again to return to "Arc" in the Con menu. Press Next until "End" is displayed then press
Enter to return to normal operation.
Selecting Fan Relay Settings – "FrS"
To select the Fan Relay setting, in normal mode, press the Next button twice to get to "Con" or the Configuration menu. Then press the
Enter button to enter the Con menu. The seventh selection is the "FrS" or Fan Relay setting. Press Next six times to get to "FrS" then
press Enter. If the fan relay is "dIS" (disabled) press Next to change it to 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19 or 20%
LEL (flashing) then press Enter to confirm the change (solid) and press Enter again to return to "FrS" in the Con menu. Press Next
until "End" is displayed then press Enter to return to normal operation.
Selecting Fan Relay Delay – "FrD"
To select the Fan Relay Delay setting, in normal mode, press the Next button twice to get to "Con" or the Configuration menu. Then
press the Enter button to enter the Con menu. The eighth selection is the "FrD" or Fan Relay Delay. Press Next seven times to get to
"FrD" then press Enter. If the delay is "0" (disabled) press Next to change it to 1, 3, 5, or 10 minutes (flashing) then press Enter to
confirm the change (solid) and press Enter again to return to "FrD" in the Con menu. Press Next until "End" is displayed then press
Enter to return to normal operation.
Selecting Fan Relay Run Time – "Frr"
To select the Fan Minimum Runtime setting, in normal mode, press the Next button twice to get to "Con" or the Configuration menu.
Then press the Enter button to enter the Con menu. The ninth selection is the "Frr" or Fan Minimum Run Time. Press Next eight
times to get to "Frr" then press Enter. If the runtime is "0" (disabled) press Next to change it to 3, 5, 10 or 15 minutes (flashing) then
press Enter to confirm the change (solid) and press Enter again to return to "Frr" in the Con menu. Press Next until "End" is displayed
then press Enter to return to normal operation.
14