Machine Data; Noise And Vibration Declaration Statement - Atlas Copco BBC 16W Prescriptions De Sécurité Et Instructions Pour L'opérateur

BBC 16W, 16WS, 34W, 34WS, 34WTH
Problem Cause
Chipping of the piston tip Misalignment of the shank
Excessive wear of the piston tip
Spline breakage Lack of lubrication
Dirt intrusion (specially when drilling
upwards)
Piston breakage Lack of lubrication
Uneven tension in the side bolts
Worn intermediate part/piston guide (can
be confirmed by the cushion test)
Side bolt breakage Uneven tension on the bolts
1
Gauge for chuck bushing 22 mm (
2
Use Atlas Copco no. 9090 0550 80 pressure gauge to test the water and air pressure.

Machine data

Type Part number
BBC 16W 8311 0401 10
BBC 16WS 8311 0303 46
BBC 34W 8311 0408 05
BBC 34WS 8311 0303 47
BBC 34WTH 8311 0408 10
Air consumption (6 bar)
Type
BBC 16W
BBC 16WS
BBC 34W
BBC 34WS
BBC 34WTH

Noise and vibration declaration statement

Guaranteed sound power level Lw according to EN ISO 3744 in accordance with directive 2000/14/EC.
Sound pressure level Lp according to EN ISO 11203.
Vibration value A and uncertainty B determined according to ISO 5349-2. See table "Noise and vibration data"
for the values of A, B, etc.
© 2012 Atlas Copco Construction Tools AB | No. 9800 0627 71f | 2012-06-30
Original instructions
7 ⁄ ") hexagon shank Atlas Copco no. 3091 0038 00.
8
Piston bore Stroke length
mm
(in.)
70
(2 3 ⁄ )
4
70
(2 3 ⁄ )
4
80
(3 1 ⁄ )
7
80
(3 1 ⁄ )
7
80
(3 1 ⁄ )
7
l/s
Impact rate (6 bar)
3
(foot /min )
69
(146)
69
(146)
88
(186)
88
(186)
88
(186)
Safety and operating instructions
Solution
Change the drill steel or chuck bushing or both
Change piston
2
Lower the water pressure if it is the same as or greater than the
air pressure
Increase lubrication or change oil
Increase regularity of servicing
Lower the water pressure if it is the same as or greater than the air
pressure
Increase lubrication or change oil
Tighten the bolts correctly
Change the worn part
Tighten the bolts correctly
Overall length
mm mm
(in.) (in.)
55 710
(2 1 ⁄ ) (28)
6
55 710
(2 1 ⁄ ) (28)
6
70 775
(2 3 ⁄ ) (30 1 ⁄ )
4 2
70 775
(2 3 ⁄ ) (30 1 ⁄ )
4 2
70 740
(2 3 ⁄ ) (29)
4
Hole diameter
mm
Hz (in.)
39 27-41
(1-1.6)
39 27-41
(1-1.6)
38 27-41
(1-1.6)
38 27-41
(1-1.6)
38 27-41
(1-1.6)
Weight Shank dimension
kg mm
(lb) (in.)
28.5 22 X 108
(63.0) (⅞ x 4¼)
29.5 22 X 108
(65.0) (⅞ x 4¼)
33.5 22 X 108
(74.0) (⅞ x 4¼)
34.5 22 X 108
(76.0) (⅞ x 4¼)
34.0 22 X 108
(75.0) (⅞ x 4¼)
Reaming hole diameter
mm
(in.)
≤76
(≤3)
≤76
(≤3)
≤76
(≤3)
≤76
(≤3)
≤76
(≤3)
25