hillvert HT-HOWSON-16TE Manuel D'utilisation page 6

HT-HOWSON-18BE
1
2
3
8
4
5
6
7
1. Housing
2. Mesh
3. Power connection
4. Rotational speed adjustment knob
5. Stand leg
6. Leaf bag
7. Stand base
8. Cover snap fastener
INSTALLING THE APPLIANCE
APPLIANCE LOCATION
Keep the device away from hot surfaces. The device should
always be kept out of reach of children and mentally
disabled person. Always ensure unobstructed access to the
electricity plug. Make sure the power source reflects the
parameters on the rating plate.
Preparing for use
HT-HOWSON-16TE/
HT-HOWSON-19TE/HT-HOWSON-24TE
1. Place mesh with blades over the bowl
2. Place cover (2) on the bowl with mesh. Ensure it is on
properly.
3. Connect power to (5), the diode (7) will not be on if
the machine is not spinning.
4. Use knob (6) to set the rotational speed for the blade
and rubbers. When in use the diode (7) will be red.
10
EN
For manual operation attach the crank as per the drawing
below.
Two types of blades can be installed in the device:
Crosswise: Lengthwise:
TO CHANGE THE BLADE:
1. Remove the cover (2).
2. Remove the mesh with blades (3) from the bowl (4).
3. Turn the mesh with blades so that the blades are
facing upwards.
4. Remove the nut and carefully remove the blade.
5. Attach new blade, tighten the nut. Reverse these
steps to assemble the device.
HT-HOWSON-18TE/HT-HOWSON-18SE
1. Place the drum with the upper surface facing down.
2. Insert stand legs into the drum, align notch with legs
in snap fastener.
3. Place stand base over the stand legs and screw
together.
4. Turn the device the right side up.
5. Mount cover to the drum.
11.05.2022
6. Screw / slide (depending on the model) waste chute
to the drum.
7. Attach bags and fasten using string pullers.
HT-HOWSON-18BE
1. Place the cover, mesh and blade with the upper side
facing down.
2. Insert stand lags on the holes as shown on the
diagram below, fasten them by tightening the on the
inside of the housing.
3. Insert perpendicular stand legs with feet in the legs
already in place. Fasten by tightening screws.
4. Attach leaf bag by pulling it over the housing and
pulling the strings. Turn the device the right side up.
USE
HT-HOWSON-16TE/
HT-HOWSON-19TE/HT-HOWSON-24TE
Prepare freshly cut branches of appropriate length, so as
to facilitate unobstructed spinning by the rubbers over the
mesh. Place the branches on the mesh with the blades, then
attach the cover. Connect the device to a power source and
use knob (6) to set rotational speed.
If manual operating mode is selected, turn the crank (1) to
move the rubbers in the cover, which when spinning will
push the branches against the mesh and drag them along
it. If using in manual mode, usually 15-30 revolutions are
enough.
The cut leaves fall into the bowl with fruits, stalks etc.
remain on the mesh.
HT-HOWSON-18TE/ HT-HOWSON-18SE
Prepare freshly cut branches of appropriate length, so as
to facilitate unobstructed spinning by the rubbers over the
mesh. Connect the device to a power source, insert plants
into the drum and ensure the chute is closed. Switch the
trimmer on suing the ON/OFF switch, use the knob to set
the required rotational speed.
11.05.2022
EN
The cut leaves fall into the bowl with fruits, stalks etc.
remain on the mesh. In order to remove parts of vegetation
remaining on the mesh, open chute cover. The drum in the
trimmers is articulated. Hold the handle and pull to release
the snap fastener holding the drum in place. This is very
useful when cleaning the device.
HT-HOWSON-18BE
Prepare freshly cut branches. Connect the device to a power
supply. Use knob to set the required blade rotational speed.
Carefully push the branch against the mesh to cut. Twist
the branch and rub it against the mesh to remove leaves
around the stem. The device has a mesh with eyelets of
various sizes from 5 to 8 [mm] facilitating cutting of various
size plants. The cut leaves fall into the bag with fruits, stalks
etc. remain in the user's hand or on the mesh.
TRANSPORTATION AND STORAGE
During transport, the machine should be protected
from shaking, falling and turning upside-down. Store it
in a properly ventilated place with dry air humidity and
without any corrosive gas.
CLEANING AND MAINTENANCE
• Always unplug the device before cleaning it and after
each use.
• To clean the surface, use cleaners without corrosive
substances.
• Store the unit in a dry, cool, free from moisture and
protected from direct sunlight exposure location.
• Never spray the device with water jets.
REGULAR CONTROL OF THE DEVICE
Check regularly if the device is damaged. In case of
damage, please stop using it immediately and contact
customer service for solving the problem
What to do in case of a problem?
Please contact customer service and prepare the following
information:
• Invoice number and serial number (the latter is to be
found on the technical plate on the device).
• If necessary, take a picture of the damaged, broken
or defective part.
• It will be easier for your customer service assistant
to determine the source of the problem if you give
a detailed and precise description of the problem.
The more detailed your information, the better
customer service will be able to solve your problem
rapidly and efficiently!
CAUTION: Never open the device without the authorization
of your customer service. This can lead to a loss of warranty!
11