Eaton ATC-300 Mode D'emploi page 21

The following setpoints are programmable if the corresponding feature is programmed.
Table 2. Programmable Features and Setpoints
Setpoint Optional
Feature
New Password
TDES
TDNE
TDEN
TDEC
NOM FREQ
NOM VOLTS
S1 UV DROP
S2 UV DROP
S1 UV PICK
S2 UV PICK
S1 OV DROP X
S2 OV DROP X
S1 OV PICK X
S2 OV PICK X
S1 UF DROP X
S2 UF DROP
S1 UF PICK X
S2 UF PICK
S1 OF DROP X
S2 OF DROP X
S1 OF PICK X
S2 OF PICK X
TDN
PLANT EXER
PE LOAD XFR
PE DAY
PE HOUR
PE MINUTE
TEST MODE
TER
TPRE
PHASES
VOLT UNBAL X
UNBAL DROP % X
UNBAL PICK % X
UNBAL DELAY X
TDEF
IN-PHASE X
IP FREQ DIFF X
SYNC TIME X
PHASE REV X
IB01602001T
ATC-300 Automatic
Transfer Switch
Controller
Setpoint Units Description
Four Digits Set New Password
Minutes: Seconds Time Delay Engine Start
Minutes: Seconds Time Delay Normal to Emergency
Minutes: Seconds Time Delay Emergency to Normal
Minutes: Seconds Time Delay Engine Cool-off
Hertz Nominal Frequency
Volts Nominal Voltage
Volts Source 1 Undervoltage Dropout
Volts Source 2 Undervoltage Dropout
Volts Source 1 Undervoltage Pickup
Volts Source 2 Undervoltage Pickup
Volts Source 1 Overvoltage Dropout
Volts Source 2 Overvoltage Dropout
Volts Source 1 Overvoltage Pickup
Volts Source 2 Overvoltage Pickup
Hertz Source 1 Underfrequency Dropout
Hertz Source 2 Underfrequency Dropout
Hertz Source 1 Underfrequency Pickup
Hertz Source 2 Underfrequency Pickup
Hertz Source 1 Overfrequency Dropout
Hertz Source 2 Overfrequency Dropout
Hertz Source 1 Overfrequency Pickup
Hertz Source 2 Overfrequency Pickup
Minutes: Seconds Time Delay Neutral
Days Plant Exerciser Programming
Plant Exerciser Load Transfer
Days Plant Exerciser Day of the Week
Hours Plant Exerciser Hour
Minutes Plant Exerciser Minute
Test Mode
Minutes Engine run test time
Seconds Pretransfer delay timer
Three phase or single phase
Volts Voltage Unbalanced
Percent Percent for Unbalanced Voltage
Dropout
Percent Percent for Unbalanced Voltage
Pickup
Seconds Unbalanced Delay Timer
Seconds Time Delay Emergency Fail Timer
In-phase Transition
Hertz In-phase Transition Frequency
Difference
Minutes In-phase Transition
Synchronization Timer
Phase Reversal
For more information visit: www.eatonelectrical.com
Instruction Booklet
Effective: January 2006
Range
0000 to 9999 0300
0 to 120 seconds 0:03
0 to 1800 seconds 0:00
0 to 1800 seconds 5:00
0 to 1800 seconds 5:00
50 or 60 Hz As ordered
120 to 600 volts As ordered
97% to 50% of NOMV 80% of NOMV in volts
97% to 50% of NOMV 80% of NOMV in volts
99% to (1UVD + 2%) 90% of NOMV in volts
99% to (2UVD + 2%) 90% of NOMV in volts
105% to 120% 115% of NOMV in volts
105% to 120% 115% of NOMV in volts
(1OVD - 2%) to 103% 110% of NOMV in volts
(2OVD - 2%) to 103% 110% of NOMV in volts
90% to 97% of NOMF 94% of NOMF in hertz
90% to 97% of NOMF 94% of NOMF in hertz
(1UFD + 1Hz) to 99% 96% of NOMF in hertz
(2UFD + 1Hz) to 99% 96% of NOMF in hertz
103% to 110% of NOMF 106% of NOMF in hertz
103% to 110% of NOMF 106% of NOMF in hertz
(1OFD - 1Hz) to 101% 104% of NOMF in hertz
(2OFD - 1Hz) to 101% 104% of NOMF in hertz
0 to 120 seconds 0:00
OFF, DAILY, 7-DAY, 14- OFF
DAY or 28 DAY
0 or 1 (1 = yes) 0
SUN, MON, TUE, WED,
THU, FRI or SAT
0 to 23 0
0 to 59 0
0, 1 or 2 (0 = No Load 0
Engine Test, 1 = Load
Engine Test, 2 = Disabled)
0 min to 600 min 5:00
0 sec to 120 sec 0:00
1 or 3 AS ORDERED
0 or 1 (1 = Enabled) 1
5 to 20% of Phase to 20%
Phase Voltage Unbalance
Dropout minus (UNBAL 10%
DROP % -2) to 3%
10 to 30 20
0 sec to 6 sec 0:06
0 or 1 (1 = Enabled) 0
0.0 Hz to 3.0 Hz 1
1 min to 60 min 5
OFF, ABC, or CBA OFF
Page 21
Factory Default