Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Sound characteristics
In accordance with EN 23746 for sound power level, as
well as EN 31202 (correction factor k3 calculated ac-
cording to Appendix A.2 of EN 31204) for the calculation
of the sound pressure level at the workstation, the sound
emission values add up to a total below the underlying
work conditions mentioned in ISO 7904 Appendix A.
Sound power level in dB (Work)
Idle speed L
= 93.8 dB (A)
WA
Processing L
= 100.6 dB (A)
WA
Sound pressure level at the workstation in dB
Idle speed L
= 88.0 dB (A)
pAeq
Processing L
= 93.7 dB (A)
pAeq
Sound power level in dB (Thickness)
Idle speed L
= 94.8 dB (A)
WA
Processing L
= 97.9 dB (A)
WA
Sound pressure level at the workstation in dB
Idle speed L
= 78.3 dB (A)
pAeq
Processing L
= 84.3 dB (A)
pAeq
The specified values are emission values and therefore do
not have to represent exact work station values at the same
time. Although there is a correlation between emission and
immission gages, it is not possible to determine reliably,
whether additional precautions are necessary or not. Cur-
rent factors of the work station affect the immission gages,
including the characteristics of the work station, other
sound sources, for example number of machines other ad-
jacent operations. The permissible work values can vary
from country to country. However, the operator should ca-
pacitate the information, in order to make an estimate of
the hazard and risk.
Information on dust emission
In accordance with the policy of the Technical Committee
for Wood on dust emission checkup (concentration param-
eter) of woodworking machines, dust emission values ap-
propriate for wood are below 2 mg/m³. As a result, after
connecting the machine to an operational dust extraction
outlet, with air speed of at least 20 m/s in adherence to the
lasting and reliable TRK-marginal values for wood dust,
effective in the Federal Republic of Germany, it can be
more.
In these operating instructions we've marked the sections that
pertain to your safety with this sign: m
m General safety instructions
Training of the operator
•
Pass on the safety warnings to all people who will work
on the machine.
•
The operator must be at least 18 years old. Apprentices
must be at least 16 years old and can only work on the
machine under supervision.
•
Persons operating the machine should not be distract-
ed.
•
Keep children away from machines connected to the
power system.
•
Wear well-fitting clothes. Take off all jewelry, rings and
wristwatches.
•
Follow all safety and danger warnings on the machine
and keep them in legible condition.
•
Caution while working: risk of injury to fingers and
hands by the rotating cutting tool.
Stability assurance
•
During assembly, please make sure that the planing
machine stands firmly on solid ground.
m Utilization in accordance
with the regulations
•
The planing machine is constructed exclusively from
offered tools and supplies for wood processing.
•
The machine complies with the valid EG machine
guidelines.
•
The machine is designed for one shift of work, power-
on time S 6 – 40%.
•
Follow all safety and danger warnings on the ma-
chine.
•
Keep all safety and danger warnings on the machine
complete and legible.
•
When using in an enclosed space, the machine must
be attached to an extraction unit.
•
To extract the wood shavings or sawdust, the machine
must be attached to an extraction unit. The velocity of
flow of the connection piece of the extraction unit must
be 20 m/s. Negative pressure 1200 Pa.
•
The automatic switch-on is available as optional equip-
ment.
Type ALV 2 Item Nr. 79104010 230 V /50 Hz
Type ALV 10 Item Nr. 79104020 400 V /230 V /50 Hz
•
When switching on, the machine runs the extraction
automatically after 2-3 seconds delay time. Thus, an
overload of the safety fuse will be prevented.
•
After switching off, the machine runs the extraction for
3-4 more seconds and then shuts off automatically.
•
The left over dust will be sucked out, as required by
the Ordinance on Hazardous Substances. This saves
electricity and reduces noise. The extraction unit runs
only during the use of the machine.
•
When operating in a commercial area, a deduster must
be employed during extraction.
Do not disconnect or remove the extraction unit or the
deduster while the machine is running.
•
Use the machine only when it is in technically sound
conditions, as well as in compliance with the law, with
awareness of safety and danger according with the op-
erating instructions! Eliminate immediately all unnec-
essary distraction that could compromise safety!
•
The safety, operation and maintenance instructions of
the manufacturer, as well as the dimensions given in
the technical specs, must be observed.
•
The applicable accident prevention regulations and
other technical safety rules of general knowledge must
be observed.
•
The machine must be used, maintained or repaired
only by a competent person who can be trusted and is
informed of the dangers. The manufacturer will not be
responsible for damages resulting from arbitrary altera-
tions to the machine.
•
The machine should only be used with the original tools
and supplies from the manufacturer.
•
All use beyond the instructions counts as noncompli-
ance with the regulations. The manufacturer does not
carry any responsibility for damages resulting from such
use, the operator will bear all risks on his own.
Assembly
Part of scope of delivery:
1 Hook wrench
1 Hex head wrench
1 Hex head wrench
1 Hex head wrench
52/55
SW 3
SW 5
SW 10
english 11
Publicité
Table des Matières
