Cycle Setting Buttons; Special Functions - LG DLE4901 Serie Mode D'emploi

Masquer les pouces Voir aussi pour DLE4901 Serie:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

28
hoW to UsE

Cycle setting buttons

Sensor dry cycles have preset settings that are selected
automatically. Manual dry cycles have default settings, but you
may also customize the settings using the cycle setting buttons.
Press the button for that option to view and select other settings.
notE
To protect your garments, not every dryness level, temperature,
or option is available with every cycle. See the Cycle guide for
details.
drY leVel
Selects the level of dryness for the cycle. Press the DRY LEVEL
button repeatedly to scroll through available settings.
• This option is only available with sensor dry cycles.
• The dryer will automatically adjust the cycle time. Selecting
MORE DRY or VERY DRY will increase the cycle time, while LESS
DRY or DAMP DRY will decrease the cycle time.
• Use a LESS DRY or DAMP DRY setting for items that you wish to
iron.
temp. control
Adjusts the temperature setting from ULTRA LOW to HIGH. This
allows precise care of your fabrics and garments. Press the TEMP.
CONTROL button repeatedly to scroll through available settings.
tIme drY
Allows you to manually select the drying time, from 20 to 60
minutes, in 10-minute increments. Use this for small loads or to
remove wrinkles. Use the MORE TIME/LESS TIME buttons to add or
reduce the drying time in 1-minute increments.
Your dryer features several additional cycle options to customize
cycles to meet your individual needs. Certain option buttons also
feature a special function (see the following page for details) that
can be activated by pressing and holding that option button for 3
seconds.
to add cycle options to a cycle:
1. Turn on the dryer and turn the cycle selector knob to select the
desired cycle.
2. Use the cycle settings buttons to adjust the settings for that
cycle.
3. Press the cycle option button(s) for the option you would like to
add. A confirmation message will be shown in the display.
4. Press the START/PAUSE button to start the cycle. The dryer will
start automatically.
wrInkle care
Selecting this option will tumble the load periodically for up to
3 hours after the selected cycle, or until the door is opened. This
is helpful in preventing wrinkles when you are unable to remove
items from the dryer immediately.
sIgnal
To turn the SIGNAL off, press the SIGNAL ON/OFF button. Press
again to turn the SIGNAL back on.

Special functions

The option buttons also activate special functions, including
CHILD LOCK, RACK DRY.
Press and hold the option button marked with the special
function
* rack drY
Use RACK DRY with items, such as wool sweaters, silk, and lingerie,
that should dry flat. RACK DRY can also be used with items that
should not be tumbled dry, such as gym shoes or stuffed animals.
Press and hold the WRINKLE CARE button for 3 seconds to activate
or deactivate the RACK DRY function.
notE
NEVER use the rack with a tumble dry cycle.
to add cycle options to a cycle:
1. With the dryer door open, slide the rack into the dryer drum.
2. Make sure it is seated evenly on the edge of the inner door rim
and resting flat on the inside of the dryer.
notE
Be sure to remove the drying rack after using the RACK DRY
cycle.
* cHIld lock
Use this option to prevent unwanted use of the dryer or to keep
cycle settings from being changed while the dryer is operating.
Press and hold the EASY IRON button for 3 seconds to activate or
deactivate the CHILD LOCK function.
The CHILD LOCK icon will be shown in the display, and all controls
are disabled except the POWER button.
notE
Once set, CHILD LOCK remains active until it is manually
deactivated. CHILD LOCK must be turned off to run another
cycle. To deactivate CHILD LOCK, press and hold the SIGNAL
button for three seconds.
* damp drY sIgnal
With this option, the dryer will signal when the load is
approximately 80% dry. This allows you to remove faster- drying
lightweight items or items that you would like to iron or hang
while still slightly damp. Press and hold the REDUCE STATIC
button for 3 seconds to activate or deactivate DAMP DRY SIGNAL.

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

Dle4902 serieDle4901w

Table des Matières