Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Controls
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Note: Hood retains last speed setting when aspiration
switch is turned off.
Description of control panel
1. Light Button
•
Press lamp button to turn ON the light on High
Intensity (Lamp state previously OFF).
•
Press lamp button to turn ON the light on Low
Intensity (Lamp state previously ON).
•
Press lamp button to turn OFF the light (Lamp state
previously ON).
2. Timer Button
•
The default timer setting is 10 minutes, and it can be
adjusted between 60 minutes and 1 minute.
•
After pressing the timer button, the control enters to a
timer setup mode, and user can adjust the timer
countdown time with the "+" and "-" buttons within 5
seconds. The timer can be initiated immediately
pressing the timer button, after setting the timer
duration or pressing the timer button twice (default 10
minutes setting).
•
If no action occurs within 5 seconds, the countdown
will start.
•
During the timer setup the "+" and "-" buttons are
dedicated to the timer and no motor action will occur.
•
Once the timer is initiated, it can be cancelled by
pressing the timer button again.
3. Display
•
Shows the hood settings.
•
The display will be lit at low intensity when the hood
is not operating.
Pressing any key the display will light up at high
intensity.
•
The display will be lit at high intensity when the hood
is operating.
If no key is pressed within a minute the display will
return to being lit at low intensity.
4. "-" Button. Speed Decrease / OFF
•
This button is used to decrease the fan speed, or
turn OFF the fan.
•
The fan will turn OFF if the "-" button is pressed and
the hood was in the first speed.
•
If the fan is at second speed and the "-" button is
pressed, the fan will be set to first speed.
•
If the fan is at third speed and the "-" key is pressed,
the fan will be set to second speed.
•
If the fan is at fourth speed and the "-" button is
pressed, the fan will be set to third speed.
•
If the fan is OFF and the "-" button is pressed, the
control backlight will light up.
5. "+" Button. Speed Increase / ON
•
This button is used to increase the fan speed, or turn
ON the fan.
•
The fan will turn ON if the "+" button is pressed and
the hood was OFF.
•
If the fan is at first speed and the "+" button is
pressed, the fan will be set to second speed.
•
If the fan is at second speed and the "+" button is
pressed, the fan will be set to third speed.
•
If the fan is at third speed and the "+" button is
pressed, the fan will be set to fourth speed.
•
If the fan is at fourth speed and the "+" button is
pressed, a beep will sound.
Clock programming
•
The clock can be reprogrammed at any time except
during an active timed function.
•
The clock can be displayed in a twelve hour format and
valid clock times are from 1:00 to 12:59.
•
The clock can be reprogrammed pressing the "Timer"
button for 3 seconds, and after, the clock can be
adjusted with the "+" and "-" buttons.
•
The user can have minute increments / decrements of 1
minute, but if the user keep pressing the "+" / "-" buttons
for more than 1 second, the increments / decrements will
be of 5 minutes.
During this option the control will round to the nearest 5
minutes.
•
The user can finish on reprogramming the clock pressing
the "Timer" button.
•
After 1 minute of no button pressed the control will
accept the programmed clock time and will add one
minute to the set clock.
Grease filter saturation alarm (Optional)
•
After thirty fan functional hours, the display will show
"Grease Filter" if the fan is active.
When this icon is shown in the display, the grease filters
installed are required to be washed.
•
To reset the grease filter saturation alarm the user must
press the "+" button for 5 seconds, after this action the
icon "Grease filter" is not displayed, and the hood has
the normal display operation.
Charcoal filter saturation alarm (Optional)
•
After one hundred and twenty functional hours of the fan,
the display will show "Charcoal Filter" if the fan is
active. When this icon flashes on display, the charcoal
filters
installed
reactivated.
•
To reset the charcoal filter saturation indication the user
must press the "-" button for 5 seconds, after this time
the icon "Charcoal filter" is not displayed and the hood
has the normal display operation.
Audible signal activation and deactivation
•
The audible signals can be activated or deactivated
pressing the "Light" button for 5 seconds.
•
If the audible signal is activated, a tone must sound and
the "Snd" symbol must appear on the display for 3
seconds.
•
If the audible signal is deactivated, the "Snd" symbol
must appear on the display for 3 seconds and no tone
must sound.
12
are
required
to
be
replaced
or
Publicité
Chapitres
Table des Matières
