When Alarm Sounds - DSC WTK5504 Manuel D'utilisation

Auto-Arm On/Off
When this button is pressed and the auto-arm feature is currently disabled, "Auto-Arm Enabled" is displayed on the
button and acknowledgment beeps sound. If the button is pressed and the late-to-close feature is enabled, "Auto-Arm
Disabled" is displayed on the keypad and error tone sounds.
Notes: This feature is partitionable, and therefore this feature will only be enabled on Partition 1 of a PowerSeries
panel. If this is attempted on an SCW or Alexor, the feature does not exist, and will return with "Function Not Avail-
able" and sound an error tone.
Enable DLS/Allow System Service
Home > More > User Options > User Functions [Master Code] > DLS Enable
From time to time, your installer may need to send information to or retrieve information from your security system.
Your installer will do this by having a computer call your system over the telephone line. If enabled, the installer will
be able to access Installer Programming via remote (DLS). In case of DLS access this provides a window where rings
will be detected by the panel. When enabled, the keypad sounds acknowledgment beeps.
You may need to prepare your system to receive this 'downloading' call. To do this press Enable DLS.
This allows downloading for a limited period of time. During this time, the system will answer incoming downloading
calls. The DLS window will remain open for 6 hrs, during which time the installer will be able to enter DLS an unlim-
ited number of times. After the 6-hr window has expired, Installer's Programming will be unavailable again until the
window is re-opened.
For more information on this feature, please ask your installer.
NOTE: Neither remote arming nor downloading are applicable in UL/ULC installations.
User Call-Up
Home > More > User Options > User Functions [Master Code] > DLS Call-Up
If enabled by the installer, the panel will make 1 attempt to call the downloading computer. The downloading computer
must be waiting for the panel to call before downloading can be performed. If enabled on the panel, the keypad sounds
acknowledgment beeps; if disabled, the keypad sounds an error tone and displays "Function not available".
Troubles
When a trouble condition is detected, the Trouble (
every 10 seconds. Press anywhere on the keypad to silence the beeps. Press (
press the specific option for further information.
Troubles
Service Required
(Press for more
details)
AC Trouble
Phone Trouble
Communication
Failure
Device Fault
Device Tamper
Device Low Battery
Time and Date
Trouble
Alternate
Communicator
Trouble
Alarms

When Alarm Sounds

The system can generate 3 different alarm sounds:
• Temporal/pulsed siren = Fire Alarm
• 4 beeps, 5-second pause, 4 beeps = Carbon Monoxide Alarm
• Continuous siren = Intrusion (Burglary Alarm)
NOTE: The priority of signals is fire alarm, carbon monoxide alarm then burglary alarm.
Comments/Further Options
• Panel low battery
• Bell circuit trouble
• General system trouble
• General system tamper
If the building and/or neighborhood has lost electrical power, the system
will continue to operate on battery for several hours.
The system has detected that the telephone line is disconnected.
The system attempted to communicate with the monitoring station, but
failed. This may be due to Telephone Line Fault.
• Keypads
• Repeaters (Impassa SCW9055/57)
• Zones
• Sirens
• Keypads
• Repeaters (Impassa SCW9055/57)
• Zones
• Sirens
• Repeaters (Impassa SCW9055/57)
If complete power was lost (AC and Battery), the time and date need to be
reprogrammed.
• SIM Lock
• GSM
• Ethernet
) indicator will turn on, and the keypad will sound double beeps
• Module supervision
• Rf Jam condition detected
• PC5204 low battery
• PC5204 AC failure
• Zones
• Sirens
• Keypads
• Prox tags
• Receiver
• Supervision
• Config SMS
) to view the trouble condition, and
Action
Call for service
Call for service
Call for service
Call for service
Call for service
Call for service
Call for service
Reprogram time
& date
Call for service.
For Ethernet
trouble, check
LAN
connections.
12