Warnings Regarding Installation; Usage Warnings; Guarantee Provisions; Technical Data - Niko 330-00700 Manuel D'installation

330-00700
The dimmer switches off by The protection against thermal
itself. The red LED on the overload (temperature is too
dimmer is flashing. high) and short circuits has
been activated.
The dimming profile is wrong.
The lamp is flashing. The lamp is not dimmable.
The minimal dimming level is
set too low.
The dimming profile is wrong.
There is a PLC malfunction.
The lamp is not suitable.
The dimmer is defect.
The lamp cannot be switched There is current leakage.
off.

5. USAGE WARNINGS

- Control signals that are sent via the mains can interfere with the operation of the dimmer. (This is not a
defect.)
- The dimmer is never electrically separated from the mains due to the operation of the control. Therefore, all
parts remain "live" even if the load (e.g. the light) is "off".
- This appliance is not suitable for controlling motors.

6. TECHNICAL DATA

- Power supply voltage: 230 Vac ± 10%, frequency 50 Hz
- Mounting: DIN-rail (1 U)
- Weight: ± 70 g
- Allowable ambient temperature (t a ): see power consumption graph
- Designed for use in an environment with a non-condensing atmospheric humidity (30% - 70%)
- No-load power consumption: ± 0.6 W
- Maximum temperature of the housing (t c ): 90°C
- Maximum wire diameter per connection terminal: 2.5 mm²
- Power supply and load: 2 x 1.5 mm² or 1 x 2.5 mm²
- Input: 2 x 1.5 mm² or 1 x 2.5 mm²
- Minimum load: 5 W
- Protections: thermal overload protection, short-circuit protection
- Push buttons for control: 230 Vac, 5 mA or 8-24 Vac/Vdc
- Maximum distance to last push button: 100 m
- Complies with the EN60669-2-1 standards
- Power consumption graph: consumption in function of the ambient temperature
100 %
95 %
90 %
85 %
80 %
75 %
70 %
65 %
60 %
55 %
50 %
0 10
8
EN nv Niko sa
Check if the lamp is dimmable. This
is shown on the packaging by the
following symbol:
Check whether the load is too high.
When doing this, keep in mind the
reactive power of ferromagnetic
transformers.
Check the temperature in the cabinet
(max 35° C) or create more distance
between the dimmer and the adjoi-
ning module.
Check whether mixed loads are
being used.
For LED lamps, use the profiles in the
following order of preference:
- LED 1
- Incandescent lamp
- LED 3 (with boost function)
Check if the lamp is dimmable. This
is shown on the packaging by the
following symbol:
Increase the minimum dimming level
or use a profile with boost function
(LED 3 or LED 4).
Choose another profile and adjust the
minimum dimming level.
Place a PLC filter (Ripple Control
Rejector)
Replace the lamp if it flashes during
dimming the light up and down.
Replace the dimmer
Place a bypass
20 30 40
Ambient temperature (°C)
Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu

7. WARNINGS REGARDING INSTALLATION

• The installation should be carried out by a registered installer and in compliance with the statutory regulations.
• This user manual should be presented to the user. It should be included in the electrical installation file,
and it should be passed on to any new owners. Additional copies are available on the Niko website or via
the Niko support service.
• During installation, the following should be taken into account (non-exhaustive list):
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope
of each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find the
EC declaration of conformity regarding this product at www.niko.eu.
8. NIKO SUPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.

9. GUARANTEE PROVISIONS

• The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of
purchase of the product by the consumer. If there is no invoice, the date of production applies.
• The consumer is obliged to inform Niko in writing about the non-conformity, within two months after
stating the defect.
• In case of a non-conformity, the consumer only has the right to a product repair or replacement free of
charge, which shall be decided by Niko.
• Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
• The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
Do not dump this product with the unsorted waste. Bring it to a recognised waste collection point. Together with producers
and importers, you have an important role to play in the advancement of sorting, recycling and reusing discarded electrical
and electronic appliances. In order to finance the waste collection and processing, the government levies a recycling
contribution in some cases (included in the purchase price of this product).
50 60
PM330-00700R15492